Coilcraft, Inc. 2009
Specifications subject to change without notice.
Please check our website for latest information.
Chip Inductors –1008AF Series (2520)
Document 578-1
Revised 05/29/09
Inductance2
Percent
SRF min5
DCR max6
Isat7
Irms8
Part number1
(H)
tolerance3
Q typ4
(MHz)
(Ohms)
(A)
1008AF-901X_L_
0.9
10,5
25
415
0.100
1.4
1.3
1008AF-112X_L_
1.1
10,5
24
376
0.105
1.3
1.2
1008AF-132X_L_
1.3
10,5
37
198
0.110
1.2
1.1
1008AF-152X_L_
1.5
10,5
22
135
0.125
1.1
1.0
1008AF-192X_L_
1.9
10,5
29
126
0.140
1.0
1008AF-222X_L_
2.2
10,5
21
106
0.155
0.95
1008AF-272X_L_
2.7
10,5
22
70
0.190
0.80
0.90
1008AF-332X_L_
3.3
10,5
21
59
0.210
0.75
0.80
1008AF-392X_L_
3.9
10,5
21
55
0.220
0.70
0.80
1008AF-472X_L_
4.7
10,5
27
48
0.435
0.70
0.65
1008AF-582X_L_
5.8
10,5
21
37
0.280
0.55
0.75
1008AF-682X_L_
6.8
10,5
20
33
0.315
0.50
0.70
1008AF-822X_L_
8.2
10,5
20
34
0.395
0.50
0.65
1008AF-103X_L_
10.0
10,5
22
26
0.480
0.45
0.55
Lowest DCR and highest current rating of our 1008 size
inductors
Available in 14 inductance values from 0.9 to 10 H.
1. When ordering, specify tolerance, termination and packaging codes:
1008AF-103X
JLC
Tolerance:
J = 5% K = 10%
(Table shows stock tolerances in bold.)
Termination: L = RoHS compliant silver-palladium-platinum-glass frit.
Special order: T = RoHS tin-silver-copper (95.5/4/0.5)
or S = non-RoHS tin-lead (63/37).
Packaging:
C =7
″ machine-ready reel. EIA-481 embossed plastic
tape (2000 parts per full reel).
B = Less than full reel. In tape, but not machine ready.
To have a leader and trailer added ($25 charge), use
code letter C instead.
D =13
″ machine-ready reel. EIA-481 embossed plastic tape.
Factory order only, not stocked (7500 parts per full reel).
2. Inductance measured at 2.5 MHz using Coilcraft SMD-A fixture in an
Agilent/HP 4286A impedance analyzer with Coilcraft-provided correlation
pieces.
3. Tolerances in bold are stocked for immediate shipment.
4. Q measured at 2.5 MHz using an Agilent/HP 4291A with an Agilent/HP
16193 test fixture.
5. SRF measured using an Agilent/HP 8753D network analyzer with a
Coilcraft SMD-D fixture.
6. DCR measured on a Cambridge Technology Micro-ohmmeter.
7. DC current at which the inductance drops 10% (typ.) from its value
without current.
8. Current that causes a 40°C temperature rise from 25°C ambient.
9. Electrical specifications at 25°C.
Refer to Doc 362 “Soldering Surface Mount Components” before soldering.
For part marking data, see Color Coding section.
Designer’s Kit C414 contains 10 of each 5% value
Core material Ferrite
Terminations RoHS compliant silver-palladium-platinum-glass frit.
Other terminations available at additional cost.
Weight 28 – 33 mg
Ambient temperature –40°C to +85°C with
Irms current, +85°C to
+125°C with derated current
Storage temperature Component: –40°C to +125°C.
Packaging: –40°C to +80°C
Resistance to soldering heat Max three 40 second reflows at
+260°C, parts cooled to room temperature between cycles
Temperature Coefficient of Inductance (TCL) +100 to +350 ppm/°C
Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C /
85% relative humidity)
Mean Time Between Failures (MTBF) One billion hours
Packaging 2000 per 7
″reel; 7500 per 13″ reel
Plastic tape: 8 mm wide, 0.3 mm thick, 4 mm pocket spacing,
2.0 mm pocket depth
PCB washing Only pure water or alcohol recommended
Request free evaluation samples by contacting Coilcraft
or visiting www.coilcraft.com.