参数资料
型号: 333-2SYGT/S530-E2
厂商: Everlight Electronics Co Ltd
文件页数: 7/7页
文件大小: 436K
描述: LED 5MM BRILL YLW-GRN GRN TRANSF
标准包装: 500
颜色: 绿
Millicandela 等级: 400mcd
正向电压: 2V
电流 - 测试: 20mA
波长 - 主: 573nm
波长 - 峰值: 575nm
视角: 10°
透镜类型: 透明,有色
透镜样式/尺寸: 圆形,带圆顶,5mm
封装/外壳: 径向
高度: 8.60mm
安装类型: 通孔
包装: 散装
DATASHEET
LAMP 
333-2SYGT/S530-E2
 
 
7 
Copyright ?2010, Everlight All Rights Reserved. Release Date : Apr.08. 2013. Issue No: DLE-0002169_Rev.3
www.everlight.com 
 
 
 
Wave soldering parameter must be set and maintain according to recommended temperature and dwell time in the solder
wave.
4.    Cleaning
 
When necessary, cleaning should occur only with isopropyl alcohol at room temperature for a duration of no more than
one minute. Dry at room temperature before use.
 
Do not clean the LEDs by the ultrasonic. When it is absolutely necessary, the influence of ultrasonic cleaning on the LEDs
depends on factors such as ultrasonic power and the assembled condition. Ultrasonic cleaning shall be pre-qualified to
ensure this will not cause damage to the LED
5.    Heat Management
 
Heat management of LEDs must be taken into consideration during the design stage of LED application. The current
should be de-rated appropriately by referring to the de-rating curve found in each product specification.
 
The temperature surrounding the LED in the application should be controlled. Please refer to the data sheet de-rating
curve.
6.   ESD (Electrostatic Discharge)
 
The products are sensitive to static electricity or surge voltage. ESD can damage a die and its reliability.
When handling the products, the following measures against electrostatic discharge are strongly
recommended:
Eliminating the charge
Grounded wrist strap, ESD footwear, clothes, and floors
Grounded workstation equipment and tools
ESD table/shelf mat made of conductive materials
 
Proper grounding is required for all devices, equipment, and machinery used in product assembly.
Surge protection should be considered when designing of commercial products.
 
If tools or equipment contain insulating materials such as glass or plastic,
the following measures against electrostatic discharge are strongly recommended:
Dissipating static charge with conductive materials
Preventing charge generation with moisture
Neutralizing the charge with ionizers
7.    Directions for use
 
The LEDs should be operated with forward bias. The driving circuit must be designed so that the LEDs are not subjected
to forward or reverse voltage while it is off. If reverse voltage is continuously applied to the LEDs, it may cause migration
resulting in LED damage.
8.    Other
 
Above specification may be changed without notice. EVERLIGHT will reserve authority on material change for above
specification.
 
When using this product, please observe the absolute maximum ratings and the instructions for using outlined in these
specification sheets. EVERLIGHT assumes no responsibility for any damage resulting from use of the product which does
not comply
with the absolute maximum ratings and the instructions included in these specification sheets.
 
These specification sheets include materials protected under copyright of EVERLIGHT corporation. Please dont
reproduce or cause anyone to reproduce them without EVERLIGHTs consent.
 
相关PDF资料
PDF描述
333-2UYC/S530-A3 LED 5MM SUPER YELLOW CLEAR RND
333-2UYD/S530-A3 LED 5MM SUPER YELLOW DIFF RND
334-15/T2C1-1UWA LED 5MM WHITE WATER CLEAR ROUND
383-2UYC/S400-A6 LED 5MM SUPER YELLOW WATER CLEAR
4300F5LC LED GREEN BRITE T-1
相关代理商/技术参数
参数描述
333-2UBC 制造商:ROITHNER 制造商全称:ROITHNER 功能描述:T-1 3/4(5mm) High Intensity LEDs
333-2UBC/C430 制造商:ROITHNER 制造商全称:ROITHNER 功能描述:T-1 3/4(5mm) High Intensity LEDs
333-2UBC-C430 制造商:EVERLIGHT 制造商全称:Everlight Electronics Co., Ltd 功能描述:5.0mm Round Type LED Lamps
333-2UBGC 制造商:EVERLIGHT 制造商全称:Everlight Electronics Co., Ltd 功能描述:5.0mm Round Type LED Lamps
333-2UBGC/H3/S400-A4 功能描述:标准LED-通孔 Bluish Green RoHS:否 制造商:Vishay Semiconductors 照明颜色:Red 光强度:0.7 mcd 波长/色温:615 nm 显示角:45 deg 透镜颜色/类型:Clear, Non-Diffused 正向电流:70 mA 正向电压:1.83 V to 3.03 V LED 大小:2 mm 系列: 封装:Tube