参数资料
型号: ADSP-BF544BBCZ-4A
厂商: Analog Devices Inc
文件页数: 7/100页
文件大小: 0K
描述: IC CCD SIGNAL PROCESSOR 400BGA
标准包装: 1
系列: Blackfin®
类型: 定点
接口: CAN,SPI,SSP,TWI,UART
时钟速率: 400MHz
非易失内存: 外部
芯片上RAM: 196kB
电压 - 输入/输出: 2.50V,3.30V
电压 - 核心: 1.25V
工作温度: -40°C ~ 85°C
安装类型: 表面贴装
封装/外壳: 400-LFBGA,CSPBGA
供应商设备封装: 400-CSPBGA(17x17)
包装: 托盘
Rev. C
|
Page 14 of 100
|
February 2010
ADSP-BF542/ADSP-BF544/ADSP-BF547/ADSP-BF548/ADSP-BF549
The ADSP-BF54x Blackfin processors’ CAN controllers offer
the following features:
32 mailboxes (8 receive only, 8 transmit only, 16 config-
urable for receive or transmit).
Dedicated acceptance masks for each mailbox.
Additional data filtering on first two bytes.
Support for both the standard (11-bit) and extended (29-
bit) identifier (ID) message formats.
Support for remote frames.
Active or passive network support.
CAN wakeup from hibernation mode (lowest static power
consumption mode).
Interrupts, including: TX complete, RX complete, error
and global.
The electrical characteristics of each network connection are
very demanding, so the CAN interface is typically divided into
two parts: a controller and a transceiver. This allows a single
controller to support different drivers and CAN networks. The
ADSP-BF54x Blackfin processors’ CAN module represents only
the controller part of the interface. The controller interface sup-
ports connection to 3.3 V high speed, fault-tolerant, single-wire
transceivers.
An additional crystal is not required to supply the CAN clock, as
the CAN clock is derived from the processor system clock
(SCLK) through a programmable divider.
TWI CONTROLLER INTERFACE
The ADSP-BF54x Blackfin processors include up to two 2-wire
interface (TWI) modules for providing a simple exchange
method of control data between multiple devices. The modules
are compatible with the widely used I2C bus standard. The TWI
modules offer the capabilities of simultaneous master and slave
operation and support for both 7-bit addressing and multime-
dia data arbitration. Each TWI interface uses two pins for
transferring clock (SCLx) and data (SDAx), and supports the
protocol at speeds up to 400K bits/sec. The TWI interface pins
are compatible with 5 V logic levels.
Additionally, the ADSP-BF54x Blackfin processors’ TWI mod-
ules are fully compatible with serial camera control bus (SCCB)
functionality for easier control of various CMOS camera sensor
devices.
PORTS
Because of their rich set of peripherals, the ADSP-BF54x
Blackfin processors group the many peripheral signals to ten
ports—referred to as Port A to Port J. Most ports contain 16
pins, though some have fewer. Many of the associated pins are
shared by multiple signals. The ports function as multiplexer
controls. Every port has its own set of memory-mapped regis-
ters to control port muxing and GPIO functionality.
General-Purpose I/O (GPIO)
Every pin in Port A to Port J can function as a GPIO pin, result-
ing in a GPIO pin count up to 154. While it is unlikely that all
GPIO pins will be used in an application, as all pins have multi-
ple functions, the richness of GPIO functionality guarantees
unrestrictive pin usage. Every pin that is not used by any func-
tion can be configured in GPIO mode on an individual basis.
After reset, all pins are in GPIO mode by default. Since neither
GPIO output nor input drivers are active by default, unused
pins can be left unconnected. GPIO data and direction control
registers provide flexible write-one-to-set and write-one-to-
clear mechanisms so that independent software threads do not
need to protect against each other because of expensive read-
modify-write operations when accessing the same port.
Pin Interrupts
Every port pin on ADSP-BF54x Blackfin processors can request
interrupts in either an edge-sensitive or a level-sensitive manner
with programmable polarity. Interrupt functionality is decou-
pled from GPIO operation. Four system-level interrupt
channels (PINT0, PINT1, PINT2 and PINT3) are reserved for
this purpose. Each of these interrupt channels can manage up to
32 interrupt pins. The assignment from pin to interrupt is not
performed on a pin-by-pin basis. Rather, groups of eight pins
(half ports) can be flexibly assigned to interrupt channels.
Every pin interrupt channel features a special set of 32-bit mem-
ory-mapped registers that enables half-port assignment and
interrupt management. This not only includes masking, identi-
fication, and clearing of requests, it also enables access to the
respective pin states and use of the interrupt latches regardless
of whether the interrupt is masked or not. Most control registers
feature multiple MMR address entries to write-one-to-set or
write-one-to-clear them individually.
PIXEL COMPOSITOR (PIXC)
The pixel compositor (PIXC) provides image overlays with
transparent-color support, alpha blending, and color space con-
version capabilities for output to TFT LCDs and NTSC/PAL
video encoders. It provides all of the control to allow two data
streams from two separate data buffers to be combined,
blended, and converted into appropriate forms for both LCD
panels and digital video outputs. The main image buffer pro-
vides the basic background image, which is presented in the
data stream. The overlay image buffer allows the user to add
multiple foreground text, graphics, or video objects on top of
the main image or video data stream.
ENHANCED PARALLEL PERIPHERAL INTERFACE
(EPPI)
The ADSP-BF54x Blackfin processors provide up to three
enhanced parallel peripheral interfaces (EPPIs), supporting data
widths up to 24 bits. The EPPI supports direct connection to
TFT LCD panels, parallel analog-to-digital and digital-to-ana-
log converters, video encoders and decoders, image sensor
modules and other general-purpose peripherals.
相关PDF资料
PDF描述
ADSP-21488KSWZ-4A IC CCD SIGNAL PROCESSOR 100LQFP
ADSP-21488KSWZ-3A1 IC DSP SHARC 400MHZ 100LQFP
JWS10028/A PWR SUP 28.0V 3.6A SNG OUTPUT
MAX6505UTP020+T IC TEMP SWITCH DL TRIP SOT23-6
ADSP-BF533SBBZ400 IC DSP CTLR 16BIT 400MHZ 169-BGA
相关代理商/技术参数
参数描述
AD5111 制造商:AD 制造商全称:Analog Devices 功能描述:Single-Channel, 128-/64-/32-Position, Up/Down, ±8% Resistor Tolerance, Nonvolatile Digital Potentiometer
AD5111BCPZ10-500R7 功能描述:IC DGTL POT 128POS 10K 8LFCSP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数字电位器 系列:- 标准包装:3,000 系列:DPP 接片:32 电阻(欧姆):10k 电路数:1 温度系数:标准值 300 ppm/°C 存储器类型:非易失 接口:3 线串行(芯片选择,递增,增/减) 电源电压:2.5 V ~ 6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-WFDFN 裸露焊盘 供应商设备封装:8-TDFN(2x3) 包装:带卷 (TR)
AD5111BCPZ10-RL7 功能描述:IC DGTL POT 128POS 10K 8LFCSP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数字电位器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- 接片:256 电阻(欧姆):100k 电路数:1 温度系数:标准值 35 ppm/°C 存储器类型:非易失 接口:3 线串口 电源电压:2.7 V ~ 5.25 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-WDFN 裸露焊盘 供应商设备封装:8-TDFN-EP(3x3) 包装:剪切带 (CT) 产品目录页面:1399 (CN2011-ZH PDF) 其它名称:MAX5423ETA+TCT
AD5111BCPZ80-500R7 功能描述:IC DGTL POT 128POS 80K 8LFCSP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数字电位器 系列:- 标准包装:3,000 系列:DPP 接片:32 电阻(欧姆):10k 电路数:1 温度系数:标准值 300 ppm/°C 存储器类型:非易失 接口:3 线串行(芯片选择,递增,增/减) 电源电压:2.5 V ~ 6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-WFDFN 裸露焊盘 供应商设备封装:8-TDFN(2x3) 包装:带卷 (TR)
AD5111BCPZ80-RL7 功能描述:IC DGTL POT 128POS 80K 8LFCSP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数字电位器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- 接片:256 电阻(欧姆):100k 电路数:1 温度系数:标准值 35 ppm/°C 存储器类型:非易失 接口:3 线串口 电源电压:2.7 V ~ 5.25 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-WDFN 裸露焊盘 供应商设备封装:8-TDFN-EP(3x3) 包装:剪切带 (CT) 产品目录页面:1399 (CN2011-ZH PDF) 其它名称:MAX5423ETA+TCT