- 您现在的位置：买卖IC网 > PDF目录19370 > DS1631Z+T&R (Maxim Integrated)IC THERMOMETER DIG HI-PREC 8SOIC PDF资料下载
参数资料
| 型号： | DS1631Z+T&R |
| 厂商： | Maxim Integrated |
| 文件页数： | 12/16页 |
| 文件大小： | 435K |
| 描述： | IC THERMOMETER DIG HI-PREC 8SOIC |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 功能： | 温度计，恒温计 |
| 传感器类型： | 内部 |
| 感应温度： | -55°C ~ 125°C |
| 精确度： | ±2°C（最小值） |
| 拓扑： | ADC（三角积分型），比较器，寄存器库 |
| 输出类型： | I²C?/SMBus? |
| 输出警报： | 是 |
| 输出风扇： | 无 |
| 电源电压： | 2.7 V ~ 5.5 V |
| 工作温度： | -55°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SOIC |
| 包装： | 带卷 (TR) |
DS1631/DS1631A/DS1731
12 of 15
Figure 8. START, STOP, AND ACK SIGNALS
GENERAL 2-WIRE INFORMATION
All data is transmitted MSb first over the 2-wire bus.
One bit of data is transmitted on the 2-wire bus each SCL period.
A pullup resistor is required on the SDA line and, when the bus is idle, both SDA and SCL must remain
in a logic-high state.
All bus communication must be initiated with a START condition and terminated with a STOP
condition. During a START or STOP is the only time SDA is allowed to change states while SCL is
high. At all other times, changes on the SDA line can only occur when SCL is low: SDA must remain
stable when SCL is high.
After every 8-bit (1-byte) transfer, the receiving device must answer with an ACK (or NACK), which
takes one SCL period. Therefore, nine clocks are required for every one-byte data transfer.
INITIATING 2-WIRE COMMUNICATION
To initiate 2-wire communication, the master generates a START followed by a control byte containing
the DS1631, DS1631A, or DS1731 slave address. The R/W?/SPAN>?/SPAN> bit of the control byte must be a 0 ( write )
since the master next writes a command byte. The DS1631/DS1631A/DS1731 responds with an ACK
after receiving the control byte. This must be followed by a command byte from the master, which
indicates what type of operation is to be performed. The DS1631/DS1631A/DS1731 again respond with
an ACK after receiving the command byte.
If the command byte is a Start Convert T or Stop Convert T command (see Figure 9a), the transaction is
finished, and the master must issue a STOP to signal the end of the communication sequence. If the
command byte indicates a write or read operation, additional actions must occur as explained in the
following sections.
2-WIRE WRITES
The master can write data to the DS1631/DS1631A/DS1731 by issuing an Access Config, Access TH, or
Access TL command following the control byte (see Figures 9b and 9d). Since the R/W?/SPAN>?/SPAN> bit in the control
byte was a 0 ( write ), the DS1631/DS1631A/DS1731 are already prepared to receive data. Therefore,
after receiving an ACK in response to the command byte, the master device can immediately begin
transmitting data. When writing to the configuration register, the master must send one byte of data, and
when writing to the T
H
or T
L
registers the master must send two bytes of data. After receiving each data
byte, the DS1631/DS1631A/DS1731 respond with an ACK, and the transaction is finished with a STOP
from the master.
SCL
SDA
START
Condition
STOP
Condition
ACK (or NACK)
From Receiver
相关PDF资料 |
PDF描述 |
|---|---|
| VE-211-CW-F4 | CONVERTER MOD DC/DC 12V 100W |
| TAJY337M004RNJ | CAP TANT 330UF 4V 20% 2917 |
| VE-211-CW-F3 | CONVERTER MOD DC/DC 12V 100W |
| VE-211-CW-F1 | CONVERTER MOD DC/DC 12V 100W |
| VI-211-CW-F4 | CONVERTER MOD DC/DC 12V 100W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD5171BRJZ50-R7 | 功能描述:IC DGTL POT OTP 50K SOT23-8 RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数字电位器 系列:- 标准包装:3,000 系列:DPP 接片:32 电阻（欧姆）:10k 电路数:1 温度系数:标准值 300 ppm/°C 存储器类型:非易失 接口:3 线串行（芯片选择，递增，增/减） 电源电压:2.5 V ~ 6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-WFDFN 裸露焊盘 供应商设备封装:8-TDFN（2x3） 包装:带卷 (TR) |
| AD5171BRJZ5-R2 | 功能描述:IC DGTL POT OTP 5K 12C SOT23-8 RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数字电位器 系列:- 标准包装:3,300 系列:WiperLock™ 接片:257 电阻（欧姆）:100k 电路数:1 温度系数:标准值 150 ppm/°C 存储器类型:易失 接口:3 线 SPI（芯片选择） 电源电压:1.8 V ~ 5.5 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:8-VDFN 裸露焊盘 供应商设备封装:8-DFN-EP（3x3） 包装:带卷 (TR) |
| AD5171BRJZ5-R7 | 功能描述:IC DGTL POT OTP 5K SOT23-8 RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数字电位器 系列:- 标准包装:3,000 系列:DPP 接片:32 电阻（欧姆）:10k 电路数:1 温度系数:标准值 300 ppm/°C 存储器类型:非易失 接口:3 线串行（芯片选择，递增，增/减） 电源电压:2.5 V ~ 6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-WFDFN 裸露焊盘 供应商设备封装:8-TDFN（2x3） 包装:带卷 (TR) |
| AD5171EVAL | 功能描述:BOARD EVAL FOR AD5171 RoHS:否 类别:编程器，开发系统 >> 评估演示板和套件 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:- 主要目的:电源管理，电池充电器 嵌入式:否 已用 IC / 零件:MAX8903A 主要属性:1 芯锂离子电池 次要属性:状态 LED 已供物品:板 |
| AD5172 | 制造商:AD 制造商全称:Analog Devices 功能描述:256-Position One-Time Programmable Dual-Channel I2C Digital Potentiometers |
发布紧急采购，3分钟左右您将得到回复。