- 您现在的位置：买卖IC网 > PDF目录20264 > T95R157M020EZSL (Vishay Sprague)CAP TANT 150UF 20V 20% 2824 PDF资料下载
参数资料
| 型号： | T95R157M020EZSL |
| 厂商： | Vishay Sprague |
| 文件页数： | 20/21页 |
| 文件大小： | 0K |
| 描述： | CAP TANT 150UF 20V 20% 2824 |
| 标准包装： | 600 |
| 系列： | TANTAMOUNT® T95 |
| 电容： | 150µF |
| 电压 - 额定： | 20V |
| 容差： | ±20% |
| ESR（等效串联电阻）： | 75 毫欧 |
| 类型： | 保形涂层 |
| 工作温度： | -55°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 2824（7260 公制） |
| 尺寸/尺寸： | 0.283" L x 0.236" W（7.20mm x 6.00mm） |
| 高度 - 座高（最大）： | 0.150"（3.80mm） |
| 制造商尺寸代码： | R |
| 特点： | COTS（高可靠性） |
| 包装： | 带卷 (TR) |
Conformal Coated Guide
www.vishay.com
GUIDE TO APPLICATION
Vishay Sprague
P
V R MS = Z ------------
1.
2.
AC Ripple Current: The maximum allowable ripple
current shall be determined from the formula:
I R MS =
------------
R ESR
where,
P=
Power dissipation in W at + 25 °C as given in
the tables in the product datasheets (Power
Dissipation).
R ESR = The capacitor equivalent series resistance at
the specified frequency
AC Ripple Voltage: The maximum allowable ripple
voltage shall be determined from the formula:
V RMS = I R MS x Z
or, from the formula:
P
R ESR
where,
P = Power dissipation in W at + 25 °C as given in
the tables in the product datasheets (Power
Dissipation).
R ESR = The capacitor equivalent series resistance at
the specified frequency
5.
6.
6.1
7.
Power Dissipation: Power dissipation will be
affected by the heat sinking capability of the
mounting surface. Non-sinusoidal ripple current may
produce heating effects which differ from those
shown. It is important that the equivalent I RMS value
be established when calculating permissible
operating levels. (Power dissipation calculated using
derating factor (see paragraph 4)).
Attachment:
Soldering: Capacitors can be attached by
conventional soldering techniques, convection,
infrared reflow, wave soldering and hot plate
methods. The soldering profile chart shows typical
recommended time/temperature conditions for
soldering. Preheating is recommended to reduce
thermal stress. The recommended maximum preheat
rate is 2 °C/s. Attachment with a soldering iron is not
recommended due to the difficulty of controlling
temperature and time at temperature. The soldering
iron must never come in contact with the capacitor.
Recommended Mounting Pad Geometries: The
nib must have sufficient clearance to avoid electrical
contact with other components. The width
dimension indicated is the same as the maximum
width of the capacitor. This is to minimize lateral
movement.
Z=
The capacitor impedance at the specified
frequency
8.
Cleaning (Flux Removal) After Soldering:
T ANTAMOUNT ? capacitors are compatible with all
commonly used solvents such as TES, TMS, Prelete,
2.1
2.2
3.
4.
The sum of the peak AC voltage plus the applied DC
voltage shall not exceed the DC voltage rating of the
capacitor.
The sum of the negative peak AC voltage plus the
applied DC voltage shall not allow a voltage reversal
exceeding 10 % of the DC working voltage at
+ 25 °C.
Reverse Voltage: Solid tantalum capacitors are not
intended for use with reverse voltage applied.
However, they have been shown to be capable of
withstanding momentary reverse voltage peaks of up
to 10 % of the DC rating at 25 °C and 5 % of the DC
rating at + 85 °C.
Temperature Derating: If these capacitors are to be
operated at temperatures above + 25 °C, the
permissible RMS ripple current or voltage shall be
calculated using the derating factors as shown:
TEMPERATURE
DERATING FACTOR
+ 25 °C
1.0
+ 85 °C
0.9
+ 125 °C
0.4
Chlorethane, Terpene and aqueous cleaning media.
However, CFC/ODS products are not used in the
production of these devices and are not
recommended. Solvents containing methylene
chloride or other epoxy solvents should be avoided
since these will attack the epoxy encapsulation
material.
Revision: 03-Apr-14
11
Document Number: 40150
For technical questions, contact: tantalum@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
相关PDF资料 |
PDF描述 |
|---|---|
| 195D106X9050R8T | CAP TANT 10UF 50V 10% 2824 |
| MC78M18CDTRKG | IC REG LDO 18V .5A DPAK-3 |
| T95R336M035EZSL | CAP TANT 33UF 35V 20% 2824 |
| MC78L12ABPRPG | IC REG LDO 12V .1A TO-92 |
| V375A5C300BL2 | CONVERTER MOD DC/DC 5V 300W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD7875LNZ1 | 制造商:AD 制造商全称:Analog Devices 功能描述:LC2MOS Complete, 12-Bit, 100 kHz, Sampling ADCs |
| AD7875LP | 制造商:Rochester Electronics LLC 功能描述:12 BIT SAMPLING ADC IC - Bulk 制造商:Analog Devices 功能描述: |
| AD7875LP-REEL | 制造商:AD 制造商全称:Analog Devices 功能描述:LC2MOS Complete, 12-Bit, 100 kHz, Sampling ADCs |
| AD7875LPZ | 功能描述:IC ADC 12BIT SAMPLING 5V 28-PLCC RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:- 位数:14 采样率（每秒）:83k 数据接口:串行，并联 转换器数目:1 功率耗散（最大）:95mW 电压电源:双 ± 工作温度:0°C ~ 70°C 安装类型:通孔 封装/外壳:28-DIP（0.600"，15.24mm） 供应商设备封装:28-PDIP 包装:管件 输入数目和类型:1 个单端，双极 |
| AD7875LPZ1 | 制造商:AD 制造商全称:Analog Devices 功能描述:LC2MOS Complete, 12-Bit, 100 kHz, Sampling ADCs |
发布紧急采购，3分钟左右您将得到回复。