参数资料
| 型号： | ISL12028AIV27Z-T |
| 厂商： | Intersil |
| 文件页数： | 17/29页 |
| 文件大小： | 0K |
| 描述： | IC RTC/CALENDAR EEPROM 14TSSOP |
| 产品培训模块： | Solutions for Industrial Control Applications |
| 标准包装： | 2,500 |
| 类型： | 时钟/日历 |
| 特点： | 警报器，闰年，监控器，监视计时器 |
| 时间格式： | HH:MM:SS（12/24 小时） |
| 数据格式： | YY-MM-DD-dd |
| 接口： | I²C，2 线串口 |
| 电源电压： | 2.7 V ~ 5.5 V |
| 电压 - 电源，电池： | 1.8 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 14-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 14-TSSOP |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页当前第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页
24
FN8233.9
November 30, 2010
The X1 and X2 connections to the crystal are to be kept as
short as possible. A thick ground trace around the crystal is
advised to minimize noise intrusion, but ground near the X1
and X2 pins should be avoided as it will add to the load
capacitance at those pins. Keep in mind these guidelines for
other PCB layers in the vicinity of the RTC device. A small
decoupling capacitor at the VDD pin of the chip is mandatory,
with a solid connection to ground.
For other RTC products, the same rules stated previously
should be observed, but adjusted slightly since the packages
and pinouts are slightly different.
Oscillator Measurements
When a proper crystal is selected and the layout guidelines
above are observed, the oscillator should start up in most
circuits in less than one second. Some circuits may take
slightly longer, but startup should definitely occur in less than
5 seconds. When testing RTC circuits, the most common
impulse is to apply a scope probe to the circuit at the X2 pin
(oscillator output) and observe the waveform. DO NOT DO
THIS! Although in some cases you may see a usable
waveform, due to the parasitics (usually 10pF to ground)
applied with the scope probe, there will be no useful
information in that waveform other than the fact that the
circuit is oscillating. The X2 output is sensitive to capacitive
impedance so the voltage levels and the frequency will be
affected by the parasitic elements in the scope probe.
Applying a scope probe can possibly cause a faulty oscillator
to start up, hiding other issues (although in the Intersil
RTC’s, the internal circuitry assures startup when using the
proper crystal and layout).
The best way to analyze the RTC circuit is to power it up and
read the real time clock as time advances, or if the chip has
the IRQ/FOUT output, look at the output of that pin on an
oscilloscope (after enabling it with the control register, and
using a pull-up resistor for the open-drain output).
Alternatively, the ISL12028 IRQ/FOUT- output can be
checked by setting an alarm for each minute. Using the
pulse interrupt mode setting, the once-per-minute interrupt
functions as an indication of proper oscillation.
TABLE 11. I2C, LV RESET, AND BATTERY BACKUP OPERATION SUMMARY (SHADED ROW IS SAME AS X1228 OPERATION)
MODE
SBIB
BIT
BSW
BIT
VBAT
SWITCHOVER
VOLTAGE
I2C ACTIVE IN
BATTERY
BACKUP?
EE PROM WRITE/
READ IN BATTERY
BACKUP?
IRQ/FREQ
ACTIVE?
NOTES
A
0
Standard Mode,
VTRIP = 2.2V typ,
Default for
ISL12028A
NO
YES
Operation of I2C bus down to
VDD =VRESET, then below that no
communications. Battery switchover
at VTRIP.
B
(X1228
mode)
0
1
Legacy Mode,
VDD < VBAT
Default for
ISL12028,
YES, only if
VBAT > VRESET
YES, read only
YES
Operation of I2C bus into battery
backup mode, but only for
VBAT>VDD>VRESET.
Bus must have pull-ups to VBAT. No
nonvolatile writes with VBAT>VDD
C
1
0
Standard Mode,
VTRIP = 2.2V typ
NO
YES
Operation of I2C bus down to
VDD =VRESET, then below that no
communications. Battery switchover
at VTRIP.
D
1
Legacy Mode,
VDD < VBAT
NO
YES
Operation of I2C bus down to VRESET
or VBAT, whichever is higher.
ISL12028, ISL12028A
相关PDF资料 |
PDF描述 |
|---|---|
| VE-B3L-MY-F1 | CONVERTER MOD DC/DC 28V 50W |
| DS1337U/T&R | IC RTC SERIAL 2WIRE LP 8-USOP |
| DS1337S/T&R | IC RTC SERIAL 2WIRE LP 8-SOIC |
| DS1342T+T&R | IC RTC I2C W/ALARM 6TDFN |
| DS1341T+T&R | IC RTC I2C W/ALARM 6TDFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD842JCHIPS | 制造商:AD 制造商全称:Analog Devices 功能描述:Wideband, High Output Current, Fast Settling Op Amp |
| AD842JH | 制造商:Rochester Electronics LLC 功能描述:HIGH OUTPUT CURRENT AMP - Bulk |
| AD842JHZ | 制造商:Analog Devices 功能描述:OP Amp Single GP ±18V 12-Pin TO-8 制造商:Analog Devices 功能描述:OP AMP SGL GP 18V 12PIN TO-8 - Rail/Tube |
| AD842JN | 制造商:Rochester Electronics LLC 功能描述:WIDEBAND HIGH SPEED OPAMP - Bulk 制造商:Analog Devices 功能描述:IC OP-AMP HIGH SPEED WIDEBAND |
| AD842JNZ | 功能描述:IC OPAMP GP 80MHZ 100MA 14DIP RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:1 系列:- 放大器类型:通用 电路数:4 输出类型:满摆幅 转换速率:0.028 V/µs 增益带宽积:105kHz -3db带宽:- 电流 - 输入偏压:3nA 电压 - 输入偏移:100µV 电流 - 电源:3.3µA 电流 - 输出 / 通道:12mA 电压 - 电源，单路/双路(±):2.7 V ~ 12 V，±1.35 V ~ 6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:14-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:14-TSSOP 包装:剪切带 (CT) 其它名称:OP481GRUZ-REELCT |
发布紧急采购，3分钟左右您将得到回复。