- 您现在的位置：买卖IC网 > PDF目录20877 > NDTD4812C (Murata Power Solutions Inc)CONV DC/DC 3W 48VIN 12VOUT DIP24 PDF资料下载
参数资料
| 型号： | NDTD4812C |
| 厂商： | Murata Power Solutions Inc |
| 文件页数： | 2/7页 |
| 文件大小： | 0K |
| 描述： | CONV DC/DC 3W 48VIN 12VOUT DIP24 |
| 产品培训模块： | Low Power DC/DC Converters <5W |
| 标准包装： | 15 |
| 系列： | NDTD |
| 类型： | 隔离 |
| 输出数： | 2 |
| 电压 - 输入（最小）： | 36V |
| 电压 - 输入（最大）： | 75V |
| Voltage - Output 1： | 12V |
| Voltage - Output 2： | -12V |
| 电流 - 输出（最大）： | 125mA，125mA |
| 电源（瓦） - 制造商系列： | 3W |
| 电压 - 隔离： | 1kV（1000V） |
| 安装类型： | 通孔 |
| 封装/外壳： | 24-DIP 模块（600 mil，8 引线） |
| 尺寸/尺寸： | 1.27" L x 0.58" W x 0.27" H（32.3mm x 14.7mm x 6.9mm） |
| 包装： | 管件 |
| 工作温度： | -40°C ~ 85°C |
| 效率： | 80% |
| 电源（瓦特）- 最大： | 3W |
| 产品目录页面： | 2716 (CN2011-ZH PDF) |
| 其它名称： | 811-1381-5 |
NDTD Series
Isolated 3W Wide Input Dual Output DC/DC Converters
OUTPUT CHARACTERISTICS
Parameter
Voltage set point accuracy
Conditions
With external input/output capacitors
3.3V & 5V outputs
12V & 15V outputs
Min.
Typ.
±2
±1
Max.
±5
±3
Units
%
Line regulation
Low line to high line with external input/output capacitors
0.15
0.5
%
Load regulation
25% load to 100% load with external input/output
capacitors with balanced load
3.3V & 5V outputs
12V & 15V outputs
0.5
0.2
1.0
0.5
%
%
Ripple
Ripple & noise
BW = 20Hz to 300kHz with external input/output capacitors
BW = DC to 20MHz with external input/output capacitors
15
90
40
150
mV rms
mV p-p
NDTD05XXC, NDTD1203C,
% voltage change on negative output when
NDTD1205C, NDTD2403C,
NDTD2405C, NDTD4803C,
5.0
Cross regulation
positive load varies from 12% to 50% of 3W rating,
with negative load ?xed at 50%
NDTD4805C
NDTD1212C, NDTD1215C,
NDTD2412C, NDTD2415C,
2.1
3.0
%
NDTD4812C, NDTD4815C
Short circuit protection
GENERAL CHARACTERISTICS
Continuous
Parameter Conditions
Min.
Typ.
Max.
Units
Switching frequency
100% to 25% load, VIN min to max
60
620
kHz
TEMPERATURE CHARACTERISTICS
Parameter Conditions
Operation
Storage
Min.
-40
-50
Typ.
Max.
85
130
Units
NDTD0503
54
Case temperature rise above
ambient in still air
NDTD1203C, NDTD2403C, NDTD4803C
NDTD0505C, NDTD0512C, NDTD1205C, NDTD2405C, NDTD4805C
NDTD0515C, NDTD1212C, NDTD1215C, NDTD2412C, NDTD4812C, NDTD2415C,
NDTD4815C
40
35
28
oC
ISOLATION CHARACTERISTICS
Parameter
Isolation voltage
Resistance
Conditions
Flash tested for 1 second
Viso=1KVDC
Min.
1000
1
Typ.
Max.
Units
VDC
GΩ
TECHNICAL NOTES
ISOLATION VOLTAGE
‘Hi Pot Test’, ‘Flash Tested’, ‘Withstand Voltage’, ‘Proof Voltage’, ‘Dielectric Withstand Voltage’ & ‘Isolation Test Voltage’ are all terms that relate to the same thing, a test voltage,
applied for a speci?ed time, across a component designed to provide electrical isolation, to verify the integrity of that isolation.
Murata Power Solutions NDTD series of DC/DC converters are all 100% production tested at their stated isolation voltage. This is 1kVDC for 1 second.
A question commonly asked is, “What is the continuous voltage that can be applied across the part in normal operation?”
For a part holding no speci?c agency approvals, such as the NDTD series, both input and output should normally be maintained within SELV limits i.e. less than 42.4V peak, or
60VDC. The isolation test voltage represents a measure of immunity to transient voltages and the part should never be used as an element of a safety isolation system. The part
could be expected to function correctly with several hundred volts offset applied continuously across the isolation barrier; but then the circuitry on both sides of the barrier must
be regarded as operating at an unsafe voltage and further isolation/insulation systems must form a barrier between these circuits and any user-accessible circuitry according to
safety standard requirements.
REPEATED HIGH-VOLTAGE ISOLATION TESTING
It is well known that repeated high-voltage isolation testing of a barrier component can actually degrade isolation capability, to a lesser or greater degree depending on materials,
construction and environment. The NDTD series has an EI ferrite core, with no additional insulation between primary and secondary windings of enameled wire. While parts can be
expected to withstand several times the stated test voltage, the isolation capability does depend on the wire insulation. Any material, including this enamel (typically polyurethane)
is susceptible to eventual chemical degradation when subject to very high applied voltages thus implying that the number of tests should be strictly limited. We therefore strongly
advise against repeated high voltage isolation testing, but if it is absolutely required, that the voltage be reduced by 20% from speci?ed test voltage.
This consideration equally applies to agency recognized parts rated for better than functional isolation where the wire enamel insulation is always supplemented by a further
insulation system of physical spacing or barriers.
www.murata-ps.com/support
KDC_NDTD.E05 Page 2 of 7
相关PDF资料 |
PDF描述 |
|---|---|
| NDTD0515C | CONV DC/DC 3W 5VIN 15VOUT DIP24 |
| P51-3000-A-I-M12-4.5OVP-000-000 | SENSOR 3000PSI 7/16-20UNF 4.5V |
| NDL1212SC | CONV DC/DC 2W 12VIN 12VOUT SIP |
| REC5-243.3DRWZ/H2/A/SMD/CTRL | CONV DC/DC 5W 9-36VIN +/-3.3V |
| GEC10DRAH | CONN EDGECARD 20POS R/A .100 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADM3101EARQZ-REEL1 | 制造商:AD 制造商全称:Analog Devices 功能描述:?±15 kV ESD Protected, 3.3 V Single-Channel RS-232 Line Driver/Receiver |
| ADM3120BX-AB-T-2-G | 功能描述:网络控制器与处理器 IC ROUTER / ADM RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| ADM3120BXABT2GXP | 制造商:Lantiq 功能描述:ROUTER / ADM |
| ADM3202 | 制造商:AD 制造商全称:Analog Devices 功能描述:Low Power, +3.3 V, RS-232 Line Drivers/Receivers |
| ADM3202AN | 功能描述:IC TXRX DUAL RS-232 3.3V 16DIP RoHS:否 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:- 标准包装:121 系列:- 类型:收发器 驱动器/接收器数:1/1 规程:RS422，RS485 电源电压:3 V ~ 3.6 V 安装类型:表面贴装 封装/外壳:10-WFDFN 裸露焊盘 供应商设备封装:10-DFN（3x3） 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。