- 您现在的位置：买卖IC网 > PDF目录366382 > AM28F010A-90JIB (Advanced Micro Devices, Inc.) 1 Megabit (128 K x 8-Bit) CMOS 12.0 Volt, Bulk Erase Flash Memory with Embedded Algorithms PDF资料下载
参数资料
| 型号： | AM28F010A-90JIB |
| 厂商： | Advanced Micro Devices, Inc. |
| 英文描述： | 1 Megabit (128 K x 8-Bit) CMOS 12.0 Volt, Bulk Erase Flash Memory with Embedded Algorithms |
| 中文描述： | 1兆位（128亩× 8位）的CMOS 12.0伏，整体擦除闪存的嵌入式记忆算法 |
| 文件页数： | 10/35页 |
| 文件大小： | 464K |
| 代理商： | AM28F010A-90JIB |
第1页第2页第3页第4页第5页第6页第7页第8页第9页当前第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页
10
Am28F010A
READ-ONLY MODE
When V
PP
is less than V
CC
+ 2 V, the command register
is inactive. The device can either read array or autose-
lect data, or be standby mode.
Read
The device functions as a read only memory when V
PP
< V
CC
+ 2 V.
The device has two control functions. Both
must be satisfied in order to output data. CE# controls
power to the device. This pin should be used for spe-
cific device selection. OE# controls the device outputs
and should be used to gate data to the output pins if a
device is selected.
Address access time t
ACC
is equal to the delay from
stable addresses to valid output data. The chip enable
access time t
CE
is the delay from stable addresses and
stable CE# to valid data at the output pins. The output
enable access time is the delay from the falling edge of
OE# to valid data at the output pins (assuming the ad-
dresses have been stable at least t
ACC
- t
OE
).
Standby Mode
The device has two standby modes. The CMOS
standby mode (CE# input held at V
CC
±
0.5 V), con-
sumes less than 100 μA of current. TTL standby mode
(CE# is held at V
IH
) reduces the current requirements
to less than 1 mA. When in the standby mode the out-
puts are in a high impedance state, independent of the
OE# input.
If the device is deselected during erasure, program-
ming, or program/erase verification, the device will
draw active current until the operation is terminated.
Output Disable
Output from the device is disabled when OE# is at a
logic high level. When disabled, output pins are in a
high impedance state.
Auto Select
Flash memories can be programmed in-system or in a
standard PROM programmer. The device may be sol-
dered to the circuit board upon receipt of shipment and
programmed in-system. Alternatively, the device may
initially be programmed in a PROM programmer prior
to soldering the device to the board.
The Auto select mode allows the reading out of a binary
code from the device that will identify its manufacturer and
type. This mode is intended for the purpose of automati-
cally matching the device to be programmed with its cor-
responding programming algorithm. This mode is
functional over the entire temperature range of the device.
Programming In a PROM Programmer
To activate this mode, the programming equipment
must force V
ID
(11.5 V to 13.0 V) on address A9. Two
identifier bytes may then be sequenced from the device
outputs by toggling address A0 from V
IL
to V
IH
. All other
address lines must be held at V
IL
, and V
PP
must
be
less than or equal to V
CC
+ 2.0 V while using this Auto
select mode. Byte 0 (A0 = V
IL
) represents the manufac-
turer code and byte 1 (A0 = V
IH
) the device identifier
code. For the device the two bytes are given in the table
2 of the device data sheet. All identifiers for manufac-
turer and device codes will exhibit odd parity with the
MSB (DQ7) defined as the parity bit.
Table 2.
Am28F010A Auto Select Code
Type
A0
Code
(HEX)
Manufacturer Code
V
IL
01
Device Code
V
IH
A2
相关PDF资料 |
PDF描述 |
|---|---|
| AM28F010A-90PC | 1 Megabit (128 K x 8-Bit) CMOS 12.0 Volt, Bulk Erase Flash Memory with Embedded Algorithms |
| AM28F010A-90PCB | 1 Megabit (128 K x 8-Bit) CMOS 12.0 Volt, Bulk Erase Flash Memory with Embedded Algorithms |
| AM28F010A-90PE | 1 Megabit (128 K x 8-Bit) CMOS 12.0 Volt, Bulk Erase Flash Memory with Embedded Algorithms |
| AM28F010A-90PEB | 1 Megabit (128 K x 8-Bit) CMOS 12.0 Volt, Bulk Erase Flash Memory with Embedded Algorithms |
| AM28F010A-90PI | 1 Megabit (128 K x 8-Bit) CMOS 12.0 Volt, Bulk Erase Flash Memory with Embedded Algorithms |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AM28F010A-90LC | 制造商:未知厂家 制造商全称:未知厂家 功能描述:x8 Flash EEPROM |
| AM28F010A-90PC | 制造商:AMD 制造商全称:Advanced Micro Devices 功能描述:1 Megabit (128 K x 8-Bit) CMOS 12.0 Volt, Bulk Erase Flash Memory with Embedded Algorithms |
| AM28F010A-90PCB | 制造商:AMD 制造商全称:Advanced Micro Devices 功能描述:1 Megabit (128 K x 8-Bit) CMOS 12.0 Volt, Bulk Erase Flash Memory with Embedded Algorithms |
| AM28F010A-90PE | 制造商:AMD 制造商全称:Advanced Micro Devices 功能描述:1 Megabit (128 K x 8-Bit) CMOS 12.0 Volt, Bulk Erase Flash Memory with Embedded Algorithms |
| AM28F010A-90PEB | 制造商:AMD 制造商全称:Advanced Micro Devices 功能描述:1 Megabit (128 K x 8-Bit) CMOS 12.0 Volt, Bulk Erase Flash Memory with Embedded Algorithms |
发布紧急采购，3分钟左右您将得到回复。