参数资料
型号: AM29F100T-150SCB
厂商: ADVANCED MICRO DEVICES INC
元件分类: PROM
英文描述: Quadruple 2-Input Positive-AND Gates 14-TSSOP -40 to 85
中文描述: 128K X 8 FLASH 5V PROM, 150 ns, PDSO44
封装: SOP-44
文件页数: 2/8页
文件大小: 57K
代理商: AM29F100T-150SCB
2
Am29F100 Known Good Die
S U P P L E M E N T
GENERAL DESCRIPTION
The Am29F100 in Known Good Die (KGD) form is a 1
Mbit, 5.0 Volt-only Flash memory. AMD defines KGD as
standard product in die form, tested for functionality
and speed. AMD KGD products have the same reli-
ability and quality as AMD products in packaged form.
Am29F100 Features
The Am29F100 is a 1 Mbit, 5.0 Volt-only Flash memory
organized as 131,072 bytes or 65,536 words. Word-
wide data appears on DQ0-DQ15; byte-wide data on
DQ0-DQ7. The device is designed to be programmed
in-system with the standard system 5.0 Volt V
CC
sup-
ply. A 12.0 volt V
PP
is not required for program or erase
operations. The device can also be programmed or
erased in standard EPROM programmers.
To eliminate bus contention the device has separate
chip enable (CE#), write enable (WE#) and output en-
able (OE#) controls.
The device requires only a
single 5.0 volt power sup-
ply
for both read and write functions. Internally gener-
ated and regulated voltages are provided for the
program and erase operations.
The device is entirely command set compatible with the
JEDEC single-power-supply Flash standard
. Com-
mands are written to the command register using stan-
dard microprocessor write timings. Register contents
serve as input to an internal state machine that controls
the erase and programming circuitry. Write cycles also
internally latch addresses and data needed for the pro-
gramming and erase operations. Reading data out of
the device is similar to reading from other Flash or
EPROM devices.
Device programming occurs by executing the program
command sequence. This invokes the
Embedded
Program
algorithm—an internal algorithm that auto-
matically times the program pulse widths and verifies
proper cell margin.
Device erasure occurs by executing the erase com-
mand sequence. This invokes the
Embedded Erase
algorithm—an internal algorithm that automatically pre-
programs the array (if it is not already programmed) be-
fore executing the erase operation. During erase, the
device automatically times the erase pulse widths and
verifies proper cell margin.
The host system can detect whether a program or
erase operation is complete by observing the RY/BY#
pin, or by reading the DQ7 (Data# Polling) and DQ6
(toggle)
status bits
. After a program or erase cycle
has been completed, the device is ready to read array
data or accept another command.
The
Erase Suspend
feature enables the system to put
erase on hold for any period of time to read data from,
or program data to, a sector that is not being erased.
The
sector erase architecture
allows memory sectors
to be erased and reprogrammed without affecting the
data contents of other sectors. The device is erased
when shipped from the factory.
The
hardware data protection
measures include a
low V
CC
detector automatically inhibits write operations
during power transitions. The
hardware sector pro-
tection
feature disables both program and erase oper-
ations in any combination of the sectors of memory,
and is implemented using standard EPROM program-
mers. The
temporary sector unprotect
feature allows
in-system changes to protected sectors.
The
hardware RESET# pin
terminates any operation
in progress and resets the internal state machine to
reading array data. The RESET# pin may be tied to the
system reset circuitry. A system reset would thus also
reset the device, enabling the system microprocessor
to read the boot-up firmware from the Flash memory.
The system can place the device into the
standby mode
.
Power consumption is greatly reduced in this mode.
AMD’s Flash technology combines years of Flash
memory manufacturing experience to produce the
highest levels of quality, reliability, and cost
effectiveness. The device electrically erases all bits
within a sector simultaneously via Fowler-Nordheim
tunneling. The bytes are programmed one byte at a
time using the EPROM programming mechanism of
hot electron injection.
ELECTRICAL SPECIFICATIONS
Refer to the Am29F100 data sheet, document number
18926, for full electrical specifications on the
Am29F100.
相关PDF资料
PDF描述
AM29F100T-150SE Quadruple 2-Input Positive-AND Gates 14-TSSOP -40 to 85
AM29F100T-150SEB Quadruple 2-Input Positive-AND Gates 14-TSSOP -40 to 85
AM29F100T-150SI Quadruple 2-Input Positive-AND Gates 14-TSSOP -40 to 85
AM29F100T-150SIB Quadruple 2-Input Positive-AND Gates 14-TSSOP -40 to 85
AM29F100T-70EC Quadruple 2-Input Positive-AND Gates 14-VQFN -40 to 85
相关代理商/技术参数
参数描述
AM29F100T-70EC 制造商:Advanced Micro Devices 功能描述:
AM29F160DB-120EC 制造商:Spansion 功能描述:16M (2MX8/1MX16) 5V, BOOT BLOCK, BOT, TSOP48, COM - Trays
AM29F160DB-120EI 制造商:Spansion 功能描述:16M (2MX8/1MX16) 5V, BOOT BLOCK, BOT, TSOP48, IND - Trays
AM29F160DB-70ED 制造商:Spansion 功能描述:
AM29F160DB-70EF 功能描述:闪存 16Mb 70ns 5v Parallel NOR 闪存 RoHS:否 制造商:ON Semiconductor 数据总线宽度:1 bit 存储类型:Flash 存储容量:2 MB 结构:256 K x 8 定时类型: 接口类型:SPI 访问时间: 电源电压-最大:3.6 V 电源电压-最小:2.3 V 最大工作电流:15 mA 工作温度:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体: 封装:Reel