参数资料
型号: ATS612JSB
厂商: Allegro MicroSystems, Inc.
英文描述: Silver Mica Capacitor; Capacitance:8pF; Capacitance Tolerance: 0.5pF; Series:CD17; Voltage Rating:500VDC; Capacitor Dielectric Material:Mica; Termination:Radial Leaded; Lead Pitch:5.9mm; Leaded Process Compatible:Yes RoHS Compliant: Yes
中文描述: 动态,自校准,峰值检测,差分霍尔效应齿轮齿传感器
文件页数: 12/16页
文件大小: 208K
代理商: ATS612JSB
115 Northeast Cutoff, Box 15036
Worcester, Massachusetts 01615-0036 (508) 853-5000
ATS612LSB
DYNAMIC, SELF-CALIBRATING, PEAK-DETECTING,
DIFFERENTIAL HALL-EFFECT GEAR-TOOTH SENSOR
12
Recommended Evaluation Technique
. The self-
calibrating feature of the ATS612LSB requires that a
special evaluation technique be used to measure its high-
accuracy performance capabilities. Installation inaccura-
cies are calibrated out at power on only; hence, it is
extremely important that the device be re-powered at each
air gap when gathering timing accuracy data.
Self-Calibrating Functions.
The ATS612LSB is de-
signed to minimize performance variation caused by the
large air gap variations resulting from installation by self-
calibrating at power-on. This function should be tested
using the following procedure.
1.
Set the air gap to the desired value.
2.
Power down and then power on the device.
3.
Rotate the target at the desired speed.
4.
Wait for calibration to complete (64 output pulses to
occur).
5.
Monitor output for correct switching and measure
accuracy.
6.
Repeat the above for multiple air gaps within the
operating range of the device.
7.
This can be repeated over the entire operating tem-
perature range.
Measurement of the effect of changing air gap after power
on:
1.
Set the air gap to the desired value (nominal, for
example). Rotate the target at the desired speed.
Apply power to the module. Wait for 64 output pulses
to occur. Monitor output for correct switching and
measure accuracy.
2.
Change the air gap by
±
0.25 mm. Do not re-power
module. Monitor the output for correct switching and
measure accuracy.
Gear Diameter and Pitch
. Signal frequency is a direct
function of gear pitch and rotational speed (RPM). The
width of the magnetic signal in degrees and, hence, the
signal slope created by the tooth is directly proportional to
the circumference of the gear (
π
Do). Smaller diameters
limit the low-speed operation due to the slower rate of
change of the magnetic signal per degree of gear rotation
(here the limitation is the droop of the capacitor versus the
signal change). Larger diameters limit high-speed opera-
tion due to the higher rate of change of magnetic signal
per degree of rotation (here the limitation is the maximum
charge rate of the capacitor versus the rate of signal
change). These devices are optimized for a 50mm gear
diameter (signal not limited by tooth width), 0.22
μ
F
capacitor, and speeds of 10 RPM to 8000 RPM. For very
large diameter gears (diameter >200 mm), the devices
must be configured with a lower value capacitor, but not
less than 0.1
μ
F. This allows for a range of 5:1 in gear
diameters.
Air Gap and Tooth Geometry.
Operating
specifications
are impacted by tooth width (T), valley width (p
c
- T) and
depth (h
t
), gear material, and gear face thickness (F). The
target can be a gear or a specially cut shaft-mounted tone
wheel made of stamped ferrous metal. In general, the
following gear or target guidelines must be followed to
achieve greater than 2mm air gap from the face of unit:
Tooth width, T.............................. >2 mm
Valley width, p
c
- T ...................... >2 mm
(Whole) depth, h
t
......................... >3 mm
Gear material............................... low-carbon steel
Gear face width (thickness), F..... >3 mm
Deviation from these guidelines will result in a
reduction of air gap and a deterioration in timing accuracy.
APPLICATIONS INFORMATION
相关PDF资料
PDF描述
ATS616LSG Dynamic Self-Calibrating Peak-Detecting Differential Hall Effect Gear Tooth Sensor
ATS616LSGTN-T Aluminum Electrolytic Radial Leaded General Purpose Capacitor; Capacitance: 22uF; Voltage: 25V; Case Size: 5x11 mm; Packaging: Cut & Form
ATS622LSB TRUE ZERO-SPEED HALL-EFFECT GEAR-TOOTH SENSOR
ATS625LSGTN-T3 True Zero-Speed Low-Jitter High Accuracy Gear Tooth Sensor
ATS625LSGTN-T True Zero-Speed Low-Jitter High Accuracy Gear Tooth Sensor
相关代理商/技术参数
参数描述
ATS612LSB 功能描述:IC SENSOR GEAR TOOTH 4LEAD RoHS:否 类别:传感器,转换器 >> 磁性 - 霍尔效应,数字式开关,线性,罗盘 (IC) 系列:- 标准包装:1 系列:- 传感范围:20mT ~ 80mT 类型:旋转 电源电压:4.5 V ~ 5.5 V 电流 - 电源:15mA 电流 - 输出(最大):- 输出类型:数字式,PWM,8.5 位串行 特点:可编程 工作温度:-40°C ~ 150°C 封装/外壳:20-SSOP(0.209",5.30mm 宽) 供应商设备封装:20-SSOP 包装:Digi-Reel® 其它名称:AS5132-HSST-500DKR
ATS612LSB_1 制造商:ALLEGRO 制造商全称:Allegro MicroSystems 功能描述:Dynamic, Self-Calibrating, Peak-Detecting, Differential Hall Effect Gear Tooth Sensor
ATS612LSG 制造商:ALLEGRO 制造商全称:Allegro MicroSystems 功能描述:DYNAMIC, SELF-CALIBRATING, PEAK-DETECTING, DIFFERENTIAL HALL-EFFECT GEAR-TOOTH SENSOR
ATS-61300D-C1-R0 功能描述:散热片 FANSINK ASSY 29.25X29.25X9.5 (MM) RoHS:否 制造商:Ampro By ADLINK 产品:Heat Sink Accessories 安装风格:Through Hole 散热片材料: 散热片样式: 热阻: 长度: 宽度: 高度: 设计目的:Express-HRR
ATS-61300K-C1-R0 功能描述:散热片 FANSINK ASSY 29.25 X 29.25 X 14.5 (MM) RoHS:否 制造商:Ampro By ADLINK 产品:Heat Sink Accessories 安装风格:Through Hole 散热片材料: 散热片样式: 热阻: 长度: 宽度: 高度: 设计目的:Express-HRR