- 您现在的位置：买卖IC网 > PDF目录16880 > CMAXQUSB+ (Maxim Integrated Products)MODULE COMMAND SMBUS/I2C PDF资料下载
参数资料
| 型号： | CMAXQUSB+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 4/16页 |
| 文件大小： | 0K |
| 描述： | MODULE COMMAND SMBUS/I2C |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 1 |
| 系列： | * |
CMAXQUSB User’s Guide
Connectors P3 and P4 are designed to allow hardware
compatibility with previous Maxim EV kit module
designs. Headers P7 and P8 allow convenient probing
of SMBus/I 2 C and SPI bus signals.
Connector P5 is used during factory test to program the
MAXQ2000 in-circuit using the JTAG interface. The
connector pinout is compatible with the MAXQ2000 EV
kit’s MAXQ-JTAG-001 board.
Platform Capabilities and Limitations
General-Purpose Input and Output (GPIO) Pins
LED1 is lit when VDD is powered. LED2, LED3, and LED4
are general-purpose software-controlled indicators, which
also connect to GPIO lines. When driven as inputs, the
output impedance should be less than 6000 ? .
SMBus/I 2 C/2-Wire Interface
The CMAXQUSB module offers “bit-banged ” I 2 C at
400kHz (full speed, the default) or 100kHz (slow speed).
Optional user-switchable SCL/SDA pullup resistors are
provided on-board. Your PC and its software limits
attainable throughput. The SMBus/I 2 C bus runs in
approximately 1.8V. No commands are sent to the
firmware during this mode, so there is no impact.
However, custom designs not requiring USB suspend
should consider removing the MAX890 to avoid this
problem.
Scripting and Data Acquisition
The CMAXQUSB can store a script of commands in its
internal memory to eliminate communication “dead
time.” A script may be repeated up to 256 times, but
branching and decision making are not supported. A
script may also have a maximum of 126 command/data
bytes. Up to 1024 bytes of data may be collected.
SMBus/I 2 C/2-Wire Bus Pullup Resistors
SMBus/I 2 C requires a pullup resistor on both SCL and
SDA. The CMAXQUSB provides 1.5k ? pullup resistors,
enabled by setting both circuits of DIP switch SW1
“ON.” If there are pullup resistors already on the bus,
disable the CMAXQUSB’s pullup resistors by setting
both circuits of SW1 “OFF.”
Jumper Tables
bursts at rated speed, but there is some variable “dead
time” between transfers due to communications over-
head. Properly written PC software can minimize this
dead time but cannot completely eliminate it.
SPI/3-Wire Interface
The CMAXQUSB module offers SPI at up to 8MHz,
using the default pin configuration. All four CPOL/CPHA
modes are supported. Your PC and its software limits
attainable throughput. The SPI bus runs in bursts at
rated speed, but there is some variable “dead time”
between transfers, due to communications overhead.
Properly written PC software can minimize this dead
time but cannot completely eliminate it.
Power Supply
The CMAXQUSB is powered by the host PC’s universal
serial bus (USB). The VDD system voltage can be con-
figured for direct USB 5V power, 3.3V, or 2.5V using
one of two on-board linear regulators. An optional
external 9V DC plug-in transformer (“wall wart”) can be
connected for any EV kit board that requires this unreg-
ulated 9V DC power supply. Both the unregulated
9V DC and regulated VDD power-supply voltages are
provided to the EV kit board on the 2 x 10 (P3) and
2 x 20 (P4) connectors. Current available to a compan-
ion EV kit is 80mA.
During USB suspend, the FT232BM drives the MAX890
JUMPER
JU1 VDD
SELECT
J2
(underneath
SW1)
J3
(underneath
SW1)
JU2
JU4
JU5
POSITION
2.5V
3.3V
5V
Open
Open
Closed
Open
Closed
Open
Closed
FUNCTION
V DD = 2.5V
V DD = 3.3V
V DD = 5V
Factory assembly option:
replaces SW1-1.
Factory assembly option:
replaces SW1-2.
Connects MAXQ2000 P6.2 to
P6.3, supporting the Maxim
1-Wire? interface.
JTAG connector P5 does not
connect to the +5V supply.
JTAG connector P5 connects to
the +5V supply.
Optional higher voltage
unregulated power supply is left
unconnected; connector P1 is
not used.
Enable optional unregulated
power supply from P1 to
connectors P3 and P4.
into a partially powered mode, bringing VDD up to
1-Wire is a registered trademark of Maxim Integrated Products, Inc.
4
相关PDF资料 |
PDF描述 |
|---|---|
| EBC24DCMI-S288 | CONN EDGECARD 48POS .100 EXTEND |
| 222D174-3-60-0 | BOOT MOLDED |
| EBC20DCAI-S189 | CONN EDGECARD 40POS R/A .100 SLD |
| VI-JNN-EY | CONVERTER MOD DC/DC 18.5V 50W |
| 222D242-4-61/42-0 | BOOT MOLDED |
相关代理商/技术参数 |
参数描述 |
|---|---|
| CMAXQUSB+ | 功能描述:界面开发工具 Evaluation Brd RoHS:否 制造商:Bourns 产品:Evaluation Boards 类型:RS-485 工具用于评估:ADM3485E 接口类型:RS-485 工作电源电压:3.3 V |
| CMB | 功能描述:12V (6.0 ~ 15.0 V) 180W AC DC Configurable Power Supply Module 制造商:excelsys technologies ltd 系列:CoolX?600 NFF 零件状态:新产品 类型:单路直流输出模块 功率（W）:180W 电流:15A 电压 - 输出:12.0 标称值，6.0 ~ 15.0 范围 标准包装:1 |
| CMB 8141-0 | 制造商:TURCK Inc 功能描述:Connector, Female, 4 Pin, Eurofast, PG9, 6-8mm cable, 18AWG, 250V, 4A |
| CMB 8151-0 | 制造商:TURCK Inc 功能描述:Connector, M12 Female Straight, FA, 5 Wire, Screw, 6-8mm, U6112 制造商:TURCK Inc 功能描述:CONNECTOR EUROFAST 制造商:TURCK Inc 功能描述:CONNECTOR, EUROFAST 制造商:TURCK Inc 功能描述:CONNECTOR, EUROFAST; For Use With:Sensors; Accessory Type:Sensor Connector; Current Rating:4A; Gender:Receptacle; No. of Contacts:5; Voltage Rating:60V ;RoHS Compliant: Yes |
| CMB 8181-0 | 制造商:TURCK Inc 功能描述:Connector, M12 FA Female Straight, 8 Wire, Screw, 6-8mm Cable, U0885-23 制造商:TURCK Inc 功能描述:CONNECTOR EUROFAST 制造商:TURCK Inc 功能描述:CONNECTOR, EUROFAST 制造商:TURCK Inc 功能描述:CONNECTOR, EUROFAST; For Use With:Sensors; Accessory Type:Sensor Connector; Current Rating:2A; Gender:Receptacle; No. of Contacts:8; Voltage Rating:60V ;RoHS Compliant: Yes |
发布紧急采购，3分钟左右您将得到回复。