- 您现在的位置：买卖IC网 > PDF目录20081 > ISL9011AIRNFZ-T (Intersil)IC REG LDO 3.3V/2.5V 10-DFN PDF资料下载
参数资料
| 型号： | ISL9011AIRNFZ-T |
| 厂商： | Intersil |
| 文件页数： | 9/11页 |
| 文件大小： | 0K |
| 描述： | IC REG LDO 3.3V/2.5V 10-DFN |
| 标准包装： | 6,000 |
| 稳压器拓扑结构： | 正，固定式 |
| 输出电压： | 3.3V，2.5V |
| 输入电压： | 2.3 V ~ 6.5 V |
| 电压 - 压降（标准）： | 0.125V @ 150mA，0.25V @ 300mA |
| 稳压器数量： | 2 |
| 电流 - 输出： | 150mA（最小），300mA（最小） |
| 电流 - 限制（最小）： | 350mA |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-VFDFN 裸露焊盘 |
| 供应商设备封装： | 10-DFN（3x3） |
| 包装： | 带卷 (TR) |
ISL9011A
Block Diagram
VIN
IS1
1V
VREF
TRIM
LDO
ERROR
AMPLIFIER
VO1
VO1
QEN1
LDO-1
LDO-2
~1.0V
VO2
EN1
EN2
CONTROL
LOGIC
BANDGAP AND
VOLTAGE
UVLO
TEMPERATURE
SENSOR
REFERENCE
GENERATOR
1.00V
GND
Functional Description
CBYP
mode. During this condition, all on-chip circuits are off, and
The ISL9011A contains all circuitry required to implement
two high performance LDOs. High performance is achieved
through a circuit that delivers fast transient response to
varying load conditions. In a quiescent condition, the
ISL9011A adjusts its biasing to achieve the lowest standby
current consumption.
The device also integrates current limit protection, smart
thermal shutdown protection, staged turn-on and soft-start.
Smart Thermal shutdown protects the device against
overheating. Staged turn-on and soft-start minimize start-up
input current surges without causing excessive device
turn-on time.
Power Control
The ISL9011A has two separate enable pins (EN1 and EN2)
to individually control power to each of the LDO outputs.
When both EN1 and EN2 are low, the device is in shutdown
9
the device draws minimum current, typically less than 0.1μA.
When one or both of the enable pins are asserted, the
device first polls the output of the UVLO detector to ensure
that VIN voltage is at least about 2.1V. Once verified, the
device initiates a start-up sequence. During the start-up
sequence, trim settings are first read and latched. Then,
sequentially, the bandgap, reference voltage and current
generation circuitry power-up. Once the references are
stable, a fast-start circuit quickly charges the external
reference bypass capacitor (connected to the CBYP pin) to
the proper operating voltage. After the bypass capacitor has
been charged, the LDO’s power-up.
If EN1 is brought high, and EN2 goes high before the VO1
output stabilizes, the ISL9011A delays the VO2 turn-on until
the VO1 output reaches its target level.
If EN2 is brought high, and EN1 goes high before VO2 starts
its output ramp, then VO1 turns on first and the ISL9011A
FN6437.1
March 7, 2008
相关PDF资料 |
PDF描述 |
|---|---|
| T95R106K050CSSS | CAP TANT 10UF 50V 10% 2824 |
| T95R187K6R3HSSL | CAP TANT 180UF 6.3V 10% 2824 |
| ISL9011AIRGCZ | IC REG LDO 2.7V/1.8V 10-DFN |
| T86D336K020EAAS | CAP TANT 33UF 20V 10% 2917 |
| VE-26T-EV-F1 | CONVERTER MOD DC/DC 6.5V 150W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS26503LN+ | 功能描述:计时器和支持产品 E1-T1-J1 Bits Element RoHS:否 制造商:Micrel 类型:Standard 封装 / 箱体:SOT-23 内部定时器数量:1 电源电压-最大:18 V 电源电压-最小:2.7 V 最大功率耗散: 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装:Reel |
| DS26504 | 制造商:Maxim Integrated Products 功能描述:T1/E1/J1 ENH BITS ELEMENT LQFP - Trays |
| DS26504_06 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:T1/E1/J1/64KCC BITS Element |
| DS26504DK | 功能描述:网络开发工具 DS26504 Dev Kit RoHS:否 制造商:Rabbit Semiconductor 产品:Development Kits 类型:Ethernet to Wi-Fi Bridges 工具用于评估:RCM6600W 数据速率:20 Mbps, 40 Mbps 接口类型:802.11 b/g, Ethernet 工作电源电压:3.3 V |
| DS26504L | 功能描述:计时器和支持产品 E1/T1/J1/64Kcc Bits Element RoHS:否 制造商:Micrel 类型:Standard 封装 / 箱体:SOT-23 内部定时器数量:1 电源电压-最大:18 V 电源电压-最小:2.7 V 最大功率耗散: 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。