- 您现在的位置：买卖IC网 > PDF目录16238 > DS2788E+ (Maxim Integrated Products)IC FUEL GAUGE W/DSP DRV 14TSSOP PDF资料下载
参数资料
| 型号： | DS2788E+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 10/32页 |
| 文件大小： | 0K |
| 描述： | IC FUEL GAUGE W/DSP DRV 14TSSOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 1 |
| 功能： | 燃料，电量检测计/监控器 |
| 电池化学： | 锂离子（Li-Ion）、锂聚合物（Li-Pol） |
| 电源电压： | 2.5 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 14-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 14-TSSOP |
| 包装： | 管件 |
| 产品目录页面： | 1437 (CN2011-ZH PDF) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页当前第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
Stand-Alone Fuel-Gauge IC with
LED Display Drivers
current-sense resistors. RSGAIN is an 11-bit value
stored in 2 bytes of the parameter EEPROM memory
block. The RSGAIN value adjusts the gain from 0 to
1.999 in steps of 0.001 (precisely 2 -10 ). The user must
program RSGAIN cautiously to ensure accurate current
measurement. When shipped from the factory, the gain
calibration value is stored in two separate locations in
the parameter EEPROM block: RSGAIN, which is repro-
grammable, and FRSGAIN, which is read only. RSGAIN
determines the gain used in the current measurement.
The read-only FRSGAIN (address B0h and B1h) is pro-
vided to preserve the factory value only and is not used
in the current measurement.
Sense Resistor Temperature
Compensation
The DS2788 is capable of temperature compensating
the current-sense resistor to correct for variation in a
sense resistor’s value over temperature. The DS2788 is
factory programmed with the sense resistor temperature
coefficient, RSTC, set to zero, which turns off the tem-
perature compensation function. RSTC is user accessi-
ble and can be reprogrammed after module or pack
manufacture to improve the current accuracy when
using a high temperature coefficient current-sense
resistor. RSTC is an 8-bit value stored in the parameter
EEPROM memory block. The RSTC value sets the tem-
perature coefficient from 0 to +7782ppm/°C in steps of
30.5ppm/°C. The user must program RSTC cautiously to
ensure accurate current measurement.
Temperature compensation adjustments are made
when the Temperature register crosses 0.5 ° C bound-
aries. The temperature compensation is most effective
with the resistor placed as close as possible to the V SS
terminal to optimize thermal coupling of the resistor to
ACR
MSB—ADDRESS 10h
the on-chip temperature sensor. If the current shunt is
constructed with a copper PCB trace, run the trace
under the DS2788 package if possible.
Current Accumulation
Current measurements are internally summed, or accu-
mulated, at the completion of each conversion period
with the results displayed in the ACR. The accuracy of
the ACR is dependent on both the current measure-
ment and the conversion time base. The ACR has a
range of 0 to 409.6mVh with an LSb (least significant
bit) of 6.25μVh. Additional read-only registers (ACRL)
hold fractional results of each accumulation to avoid
truncation errors. Accumulation of charge current
above the maximum register value is reported at the
maximum register value (7FFFh); conversely, accumu-
lation of discharge current below the minimum register
value is reported at the minimum value (8000h).
Read and write access is allowed to the ACR. The ACR
must be written MSB (most significant byte) first, then
LSB (least significant byte). The write must be complet-
ed within 3.515s (one ACR register update period). A
write to the ACR forces the ADC to perform an offset
correction conversion and update the internal offset
correction factor. Current measurement and accumula-
tion begins with the second conversion following a write
to the ACR. Writing the ACR clears the fractional values
in ACRL. ACR ’s format is shown in Figure 8, and
ACRL’s format is shown in Figure 9.
To preserve the ACR value in case of power loss, the
ACR value is backed up to EEPROM. The ACR value is
recovered from EEPROM on power-up. See the memo-
ry map in Table 3 for specific address location and
backup frequency.
R/W AND EE
LSB—ADDRESS 11h
2 15
2 14
2 13
2 12
2 11
2 10
2 9
2 8
2 7
2 6
2 5
2 4
2 3
2 2
2 1
2 0
MSb
LSb
MSb
LSb
UNITS: 6.25 μVh/R SNS
Figure 8. Accumulated Current Register (ACR) Format
10
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| EEM18DSEF-S243 | CONN EDGECARD 36POS .156 EYELET |
| UCS2C331MHD | CAP ALUM 330UF 160V 20% RADIAL |
| KS8993-EVAL | BOARD EVAL EXPERIMENT FOR KS8993 |
| UVR2W470MHD | CAP ALUM 47UF 450V 20% RADIAL |
| RP12-1205SA | CONV DC/DC 12W 9-18VIN 05VOUT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS2788E+ | 功能描述:电池管理 Stand-Alone F-Gauge w/LED Display Drvrs RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| DS2788E+T&R | 制造商:Maxim Integrated Products 功能描述: 制造商:Maxim Integrated Products 功能描述:FUEL GAUGE LI-ION/LI-POL 14TSSOP - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC FUEL GAUGE W/DSP DRV 14TSSOP |
| DS2788E+T&R | 功能描述:电池管理 Stand-Alone F-Gauge w/LED Display Drvrs RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| DS2788E+TR | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Stand-Alone Fuel-Gauge IC with LED Display Drivers |
| DS2788EVKIT+ | 功能描述:电源管理IC开发工具 RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
发布紧急采购，3分钟左右您将得到回复。