参数资料
| 型号： | X40626S14I |
| 厂商： | Intersil |
| 文件页数： | 9/22页 |
| 文件大小： | 0K |
| 描述： | IC SUPERVISOR CPU DUAL 14-SOIC |
| 标准包装： | 150 |
| 类型： | 多压监控器 |
| 监视电压数目： | 2 |
| 输出： | 开路漏极或开路集电极 |
| 复位： | 低有效 |
| 复位超时： | 最小为 100 ms |
| 电压 - 阀值： | 2.93V，4.38V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 14-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 14-SOICN |
| 包装： | 管件 |
X40626
Figure 7. Acknowledge Response From Receiver
SCL from
Master
1
8
9
Data Output
from
Data Output
from Receiver
Start
Serial Write Operations
Byte Write
For a write operation, the device requires the Slave
Address Byte and a Word Address Byte. This gives the
master access to any one of the words in the array. After
receipt of the Word Address Byte, the device responds
with an acknowledge, and awaits the next eight bits of
Figure 8. Byte Write Sequence
Acknowledge
data. After receiving the 8 bits of the Data Byte, the
device again responds with an acknowledge. The master
then terminates the transfer by generating a stop condi-
tion, at which time the device begins the internal write
cycle to the nonvolatile memory. During this internal write
cycle, the device inputs are disabled, so the device will
not respond to any requests from the master. The SDA
output is at high impedance. See Figure 8.
Signals from
the Master
S
T
A
R
T
Slave
Address
Word Address
Byte 1
Word Address
Byte 0
Data
S
T
O
P
SDA Bus
S 1 0 1 0 0 S 1 S 0 0
P
A
A
A
A
Signals from
the Slave
C
K
C
K
C
K
C
K
A write to a protected block of memory will suppress
the acknowledge bit.
Page Write
The device is capable of a page write operation. It is
initiated in the same manner as the byte write opera-
tion; but instead of terminating the write cycle after the
first data byte is transferred, the master can transmit
an unlimited number of 8-bit bytes. After the receipt of
each byte, the device will respond with an acknowl-
edge, and the address is internally incremented by
one. The page address remains constant. When the
9
counter reaches the end of the page, it “rolls over” and
goes back to ‘0’ on the same page. This means that
the master can write 64 bytes to the page starting at
any location on that page. If the master begins writing
at location 60, and loads 12 bytes, then the first 4
bytes are written to locations 60 through 63, and the
last 8 bytes are written to locations 0 through 7. After-
wards, the address counter would point to location 8 of
the page that was just written. If the master supplies
more than 64 bytes of data, then new data over-writes
the previous data, one byte at a time.
FN8119.0
March 28, 2005
相关PDF资料 |
PDF描述 |
|---|---|
| AYM10DRSD-S664 | CONN EDGECARD 20POS DIP .156 SLD |
| HBM36DSXI | CONN EDGECARD 72POS DIP .156 SLD |
| HCM36DRXI | CONN EDGECARD 72POS DIP .156 SLD |
| ASM10DRSD-S664 | CONN EDGECARD 20POS DIP .156 SLD |
| HBM36DRXI | CONN EDGECARD 72POS DIP .156 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS87C530-QCL | 功能描述:8位微控制器 -MCU EPROM MCU w/RTC RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| DS87C530-QCL+ | 功能描述:8位微控制器 -MCU EPROM MCU w/RTC RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| DS87C530-QEL | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| DS87C530-QNL | 功能描述:8位微控制器 -MCU EPROM MCU w/RTC RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
发布紧急采购，3分钟左右您将得到回复。