参数资料
| 型号： | X40626V14-2.7A |
| 厂商： | Intersil |
| 文件页数： | 10/22页 |
| 文件大小： | 0K |
| 描述： | IC SUPERVISOR CPU DUAL 14-TSSOP |
| 标准包装： | 190 |
| 类型： | 多压监控器 |
| 监视电压数目： | 2 |
| 输出： | 开路漏极或开路集电极 |
| 复位： | 低有效 |
| 复位超时： | 最小为 100 ms |
| 电压 - 阀值： | 2.23V，2.93V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 14-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 14-TSSOP |
| 包装： | 管件 |
X40626
Figure 9. Page Write Operation
(I ≤ n ≤ 63)
S
Signals from
the Master
T
A
R
T
Slave
Address
Word Address
Byte 1
Word Address
Byte 0
Data
(0)
Data
(n)
S
T
O
P
SDA Bus
S 1 0 1 0 0 S 1 S 0 0
P
Signals from
the Slave
A
C
K
A
C
K
A
C
K
A
C
K
A
C
K
Figure 10. Writing 12 bytes to a 64-byte page starting at location 60 (Wrap around).
8 Bytes
4 Bytes
address
=7
address pointer
ends here
Addr = 8
address
60
address
63
The master terminates the Data Byte loading by issuing
a stop condition, which causes the device to begin the
nonvolatile write cycle. As with the byte write operation,
all inputs are disabled until completion of the internal
write cycle. See Figure 9 for the address, acknowledge,
and data transfer sequence.
Stops and Write Modes
Stop conditions that terminate write operations must
be sent by the master after sending at least 1 full data
byte plus the subsequent ACK signal. If a stop is
issued in the middle of a data byte, or before 1 full
data byte plus its associated ACK is sent, then the
device will reset itself without performing the write. The
contents of the array will not be effected.
10
Acknowledge Polling
The disabling of the inputs during nonvolatile cycles
can be used to take advantage of the typical 5mS write
cycle time. Once the stop condition is issued to indi-
cate the end of the master’s byte load operation, the
device initiates the internal nonvolatile cycle. Acknowl-
edge polling can be initiated immediately. To do this,
the master issues a start condition followed by the
Slave Address Byte for a write or read operation. If the
device is still busy with the nonvolatile cycle then no
ACK will be returned. If the device has completed the
write operation, an ACK will be returned and the host
can then proceed with the read or write operation.
Refer to the flow chart in Figure 11.
FN8119.0
March 28, 2005
相关PDF资料 |
PDF描述 |
|---|---|
| X40626V14-2.7 | IC SUPERVISOR CPU DUAL 14-TSSOP |
| 100LSQ33000MEFC64X119 | CAP ALUM 33000UF 100V 20% SCREW |
| X40626V14 | IC SUPERVISOR CPU DUAL 14-TSSOP |
| 100LSQ27000MEFC64X99 | CAP ALUM 27000UF 100V 20% SCREW |
| X40626S14T1 | IC SUPERVISOR CPU DUAL 14-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS89C450-ENL+ | 功能描述:8位微控制器 -MCU Ultra-High-Speed Flash MCU RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| DS89C450-K00 | 功能描述:开发板和工具包 - 8051 RoHS:否 制造商:Silicon Labs 产品:Development Kits 工具用于评估:C8051F960, Si7005 核心: 接口类型:USB 工作电源电压: |
| DS89C450-KIT# | 功能描述:开发板和工具包 - 8051 Ultra-High-Speed Flash MCU RoHS:否 制造商:Silicon Labs 产品:Development Kits 工具用于评估:C8051F960, Si7005 核心: 接口类型:USB 工作电源电压: |
| DS89C450-MNG | 功能描述:8位微控制器 -MCU Ultra-High-Speed Flash MCU RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| DS89C450-MNG+ | 功能描述:8位微控制器 -MCU Ultra-High-Speed Flash MCU RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
发布紧急采购，3分钟左右您将得到回复。