- 您现在的位置：买卖IC网 > PDF目录60218 > FXP6000-32-S (POWER-ONE INC) 1-OUTPUT 5600 W AC-DC REG PWR SUPPLY MODULE PDF资料下载
参数资料
| 型号： | FXP6000-32-S |
| 厂商： | POWER-ONE INC |
| 元件分类： | 电源模块 |
| 英文描述： | 1-OUTPUT 5600 W AC-DC REG PWR SUPPLY MODULE |
| 文件页数： | 2/8页 |
| 文件大小： | 359K |
| 代理商： | FXP6000-32-S |
FEB 11, 2005 revised to JAN 09, 2007
Page 2 of 8
www.power-one.com
FXP6000 AC-DC Series Data Sheet
Output Specifications
PARAMETER
DESCRIPTION/CONDITIONS
MIN
NOM
MAX
UNITS
Output Voltage
An additional 1.0 Volt is provided to the output terminals to
32V Models:
30.4
32
33.6
Adjustment Range
provide for load lead losses.
48V Models:
45.6
48
50.4
V
Output Power
Continuous duty rating.
32V Models:
5600
Watts
48V Models:
6000
Output Current
Continuous duty rating.
32V Models:
175
A
48V Models:
125
Efficiency
Full rated load (208Vac).
32V Models:
85
88
%
48V Models:
88
91
Regulation
Load, Maximum deviation with 0 to 100% load change:
With Remote Sense connected:
0.2
With Remote Sense not connected:
0.75
%
Utilizing Droop Current Share:
2.0
Line, Under all specified operating conditions.
0.2
Ripple & Noise
Measured at mating connector w/ 0.01F + 10F Tant.
20 MHz BW:
1
% p-p
100 MHz BW:
2
Overshoot / Undershoot
Output voltage overshoot/undershoot at turn-on.
0
%
Minimum Loads
Minimum loading required to maintain regulation.
0
A
Transient Response
Maximum recovery time, to within 1% of initial set
Time:
400
s
point due to a 25% load change, 1A/s.
Deviation:
3
%
Turn-On Delay
Time required for initial output voltage stabilization after power-up.
3
s
Turn-on Rise Time
Time required for output voltage to rise from 10% to 90%.
100
ms
Interface Signals and Protection
PARAMETER (NOTE 1,2)
DESCRIPTION/CONDITIONS
MIN
NOM
MAX
UNITS
AC Power Fail Warning
Warning provided prior to Vout dropping 5% after loss of AC input.
5
ms
Auxiliary Power
Output voltage - diode isolated. Inclusive of line, load, and initial tolerances.
11.5
12.0
12.7
V
Output current.
500
mA
Current Monitor
Monitor output current over a compliance range of 0~10V.
Nominal full load output:
12.5
mA
50-100% load tolerance:
-315
0
315
A/A
<50% load tolerance:
-250
0
500
A/A
Current Share
Static sharing deviation as a percent of full-load rating
Active:
5
%
for loads >10%.
Passive:
10
Input Range Select Status
Maximum signal resistance in high input voltage range selection.
0.10
Loss of Phase Warning
Warning provided prior to protective reduction in current limit.
500
ms
Output Inhibit
Voltage required to enable supply (0.5 mA sink). (NOTE 3)
1.0
V
Output Interlock
Voltage required to enable supply (6 mA sink). (NOTE 3)
1.0
V
Output Overload Protection
Straight line current limit (above approx. 5V Vout).
32V Models:
180
188
A
48V Models:
129
134
Output Overload Warning
Signal level on overload.
2.2
V
Output Short Circuit Protection
Occurs on overload when Vout is below approx. 5V.
32V Models Iavg:
30
105
A
May operate in burst-mode.
48V Models Iavg:
21
65
Output Voltage Fault Signal
Deviation from adjusted Vout that is considered as a fault.
±3
±4
±5
%
Output Voltage Margin
Output voltage swing available through Margin pin (analog).
±4.8
±5.0
±5.2
%
Overtemperature/
Time between fault warning and shutdown.
100
ms
Fan Failure Warning
Latching shutdown.
Overvoltage Protection
Latch style overvoltage protection.
FXP6000-32:
36.3
38.4
40.5
V
FXP6000-48:
55.2
57.6
60.0
Power Supply Present Signal
Resistance to logic ground upon insertion of supply.
1000
Remote Sense
Maximum load lead loss compensation (round trip).
1.0
V
NOTES: 1) All logic outputs listed below feature a standard active pull-down output with 0.4V max at 40 mA sink capability, and a 100k pull-up to 5V.
2) In addition to those listed below, signals and front-panel LEDs are provided to indicate: overtemperature/fan fault, AC phase
imbalance, output good, interlock open, and supply inhibited. The FXP also provides 4 LED’s indicating output loading.
3) Both signals must be pulled to logic ground for the unit to operate. Enables are 100% redundant internally for applications where redundant inhibit is desirable.
Contact factory for additional design details.
相关PDF资料 |
PDF描述 |
|---|---|
| FXT-16AC1011-000 | 1 FUNCTIONS, 200 V, 5 A, DATA LINE FILTER |
| FXT-16AC1012-000 | 1 FUNCTIONS, 200 V, 5 A, DATA LINE FILTER |
| FXT-16AC1013-000 | 1 FUNCTIONS, 200 V, 5 A, DATA LINE FILTER |
| FXT-16AC1014-000 | 1 FUNCTIONS, 200 V, 5 A, DATA LINE FILTER |
| FXT-16AC1021-000 | 1 FUNCTIONS, 200 V, 5 A, DATA LINE FILTER |
相关代理商/技术参数 |
参数描述 |
|---|---|
| FXP6000-48-S | 功能描述:线性和开关式电源 High Power AC Front End 6000W (48V) RoHS:否 制造商:TDK-Lambda 产品:Switching Supplies 开放式框架/封闭式:Enclosed 输出功率额定值:800 W 输入电压:85 VAC to 265 VAC 输出端数量:1 输出电压（通道 1）:20 V 输出电流（通道 1）:40 A 商用/医用: 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:Rack 长度: 宽度: 高度: |
| FXP611.07.0092C | 制造商:Taoglas 功能描述:GPS/GLONASS/COMPASS ANTENNA 制造商:Taoglas 功能描述:ANTENNA UNIT |
| FXP612.07.0095A | 功能描述:Beidou, GLONASS, GPS Flat Patch RF Antenna 4dBi Connector, IPEX MHFI Adhesive 制造商:taoglas limited 系列:- 包装:* 零件状态:在售 频率组:UHF（1 GHz ~ 2 GHz） 频率（中心/带）:* 频率范围:* 天线类型:扁平插接线 频带数:3 VSWR:1.3 回波损耗:-23dB 增益:4dBi 功率 - 最大值:5W 特性:- 端接:连接器，IPEX MHFI 侵入防护:- 安装类型:胶合剂 高度（最大值）:- 应用:北斗，GLONASS，GPS 标准包装:100 |
| FXP70.07.0053A | 功能描述:天线 2.4GHZ FLX PCB 53MM 1.13 U.FL RoHS:否 制造商:Molex 技术类型:Cellular Antenna 频率: 带宽: 尺寸:106.7 mm L x 13 mm W |
| FXP7000 | 制造商:POWER-ONE 制造商全称:Power-One 功能描述:Distributed Power Front-End |
发布紧急采购，3分钟左右您将得到回复。