- 您现在的位置：买卖IC网 > PDF目录384457 > HV9606 (Supertex, Inc.) HV9606 Current-Mode PWM Controller with Supervisor PDF资料下载
参数资料
| 型号： | HV9606 |
| 厂商： | Supertex, Inc. |
| 英文描述： | HV9606 Current-Mode PWM Controller with Supervisor |
| 中文描述： | HV9606电流模式PWM控制器，带有监 |
| 文件页数： | 6/9页 |
| 文件大小： | 565K |
| 代理商： | HV9606 |
6 4/15/2002-R.L2
Supertex, Inc. 1235 Bordeaux Drive, Sunnyvale, CA 94089 TEL: (408) 744-0100 FAX: (408) 222-4895 www.supertex.com
HV9606
Functional Description – Continued
Start-Up Regulator
The start-up regulator guarantees a maximum V
IN
pin leakage
current of 6
μ
A at 20V at the V
IN
pin while it is inhibited by the
START/STOP circuit. When the effective input voltage exceeds
the programmed START voltage, the regulator is turned on and
seeks to provide a nominal 2.9V at the V
DD
pin, which is the supply
voltage for all internal circuitry within the HV9606 except the
start/stop circuit. This regulator is capable of input voltages up to
250 Volts, which is the typical maximum arrester voltage limit used
to provide protection on telephone wires. Due to the high voltage
rating of the regulator the HV9606 can be used for applications
operating from rectified AC mains up to 140Vrms. The regulator
can supply a minimum of 5mA, which is sufficient to power the
internal circuitry and provide gate drive power for the external
MOSFET until the bootstrap circuit from the output of the PWM
drives the voltage on the V
DD
pin higher than the regulator set
point. This forces the regulator to turn off and reduce the input
current at the Vin pin to leakage levels. The V
DD
pin is typically
bypassed with a capacitor of at least 1
μ
F, which provides the peak
currents required by the voltage doubler and in turn the gate driver
for the external MOSFET.
For low power applications the circuit may be operated without
bootstrapping. Care should be taken to assure that the power
dissipation in the regulator does not become excessive, as it might
be if the input voltage is high and the gate drive energy required is
high (operating at high frequency).
Low voltage operation of the HV9606 is also possible by powering
V
DD
from supply voltages of 2.9V to 5.5V. In these applications the
Vin, START and STOP pins should be connected to SGND pin.
When powering only via V
DD
, the START/STOP control is not
available and the startup regulator circuit is not used.
V
DD
Under Voltage Lockout
To guarantee correct operation, internal circuitry is held reset by an
under voltage lockout (V
DD
UVLO) until the regulator output voltage
is at least 100mV below the startup regulator set point. To
guarantee stable starting the V
DD
UVLO has a hysteresis of
100mV.
Oscillator
The oscillator circuit operates at twice the PWM output frequency.
The frequency can be programmed in the range of 30kHz to
800kHz by means of a single resistor connected from the RT pin to
SGND. For a given frequency the value of the resistor can be
calculated using the following equation:
R
T
= [(1 / f
OSC
) –1x10
-7
] / 42.6x10
-12
Synchronization
The SYNC pin is an input/output (I/O) port to a unique fault tolerant
peer-to-peer and/or to master clock synchronization circuit. For
synchronization the SYNC pins of multiple HV9606 based
converters can be connected together and may also be connected
to the open drain/collector output of an external master clock.
When connected in this manner the oscillators will lock to the
device with the highest operating frequency. The LOW duty cycle
of an external master clock should not exceed 50%. When
synchronized in this manner, a permanent logic HIGH or LOW
condition on the SYNC pin will result in a loss of synchronization,
but the HV9606 based converters will continue to operate at their
individually set operating frequency. For this reason the SYNC pin
is considered fault tolerant, since loss of synchronization will not
result in total system failure.
Depending on the cumulative parasitic capacitance on the SYNC
pin when connected in the above manner a pull up resistor may be
required from the SYNC pin to the V
DD
pin on each HV9606 based
DC/DC converter circuit. The value of the resistor will depend on
the cumulative parasitic capacitance and operating frequency.
Voltage Doubler
The HV9606 can operate on internal voltages ranging from 2.9V to
5.5V. It may be difficult to find power MOSFETs capable of
operating with such low gate drive voltages. For this reason the
HV9606 incorporates a voltage doubler circuit that generates a
voltage on the VX2 pin that is approximately two times the V
DD
voltage. This circuit uses capacitive charge transfer methods and
requires the connection of a capacitor (typically 0.01
μ
F) between
the CA and CB pins as well as an energy storage capacitor
(typically 0.1
μ
F) connected from the VX2 pin to PGND pin. The
voltage doubler operates at the PWM output frequency.
The gate driver output on the GATE pin operates from the VX2
voltage, logic level (5Volt) gate power MOSFETs may be used
when V
DD
is bootstrapped at 3.3V or standard (10V) gate
MOSFETs may be used when V
DD
is bootstrapped at 5V.
VX2 Under Voltage Lockout
To guarantee that sufficient gate drive voltage is available, an
under voltage lockout circuit (VX2 UVLO) monitors the VX2
voltage. If the VX2 voltage drops below 4.5V the gate driver output
of the PWM circuit is inhibited to prevent damage to the power
MOSFET. This under voltage lockout has a hysteresis of 400mV
to prevent spurious operation.
Band Gap Reference
The operating limits of all internal circuits, except the
START/STOP circuit, are based on the
!
1% tolerance band gap
reference voltage available on the REF pin. It is capable of
delivering 100
μ
A for use by external circuitry without degrading the
reference. A bypass capacitor of at least 0.1
μ
F should be
connected from the REF pin to SGND pin.
相关PDF资料 |
PDF描述 |
|---|---|
| HV9606DB1 | Current-Mode PWM Multiple Output Flyback Converter |
| HV9606SP | HV9606 Current-Mode PWM Controller with Supervisor |
| HV9606X | HV9606 Current-Mode PWM Controller with Supervisor |
| HV9808 | 32-Channel Serial To Parallel Converter With High Voltage Push-Pull Outputs(最大输出电压80V，带推挽输出的32通道低压串行到高压并行转换器) |
| HV9708 | 32-Channel Serial To Parallel Converter With High Voltage Push-Pull Outputs(最大输出电压80V，带推挽输出的32通道低压串行到高压并行转换器) |
相关代理商/技术参数 |
参数描述 |
|---|---|
| HV9606DB1 | 功能描述:电源管理IC开发工具 HV9606 Demo Brd RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| HV9606DB2 | 功能描述:电源管理IC开发工具 HV9606 Demo Brd RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| HV9606SP | 功能描述:开关变换器、稳压器与控制器 Crnt Mode PWM RoHS:否 制造商:Texas Instruments 输出电压:1.2 V to 10 V 输出电流:300 mA 输出功率: 输入电压:3 V to 17 V 开关频率:1 MHz 工作温度范围: 安装风格:SMD/SMT 封装 / 箱体:WSON-8 封装:Reel |
| HV9606X | 制造商:SUPERTEX 制造商全称:SUPERTEX 功能描述:HV9606 Current-Mode PWM Controller with Supervisor |
| HV9608 | 制造商:SUPERTEX 制造商全称:SUPERTEX 功能描述:Active Clamp Current-Mode PWM Controller |
发布紧急采购，3分钟左右您将得到回复。