- 您现在的位置：买卖IC网 > PDF目录8956 > ICS1562BM-201-4LFT (IDT, Integrated Device Technology Inc)IC VIDEO CLK SYNTHESIZER 16-SOIC PDF资料下载
参数资料
| 型号： | ICS1562BM-201-4LFT |
| 厂商： | IDT, Integrated Device Technology Inc |
| 文件页数： | 15/20页 |
| 文件大小： | 0K |
| 描述： | IC VIDEO CLK SYNTHESIZER 16-SOIC |
| 标准包装： | 2,500 |
| 类型： | 时钟/频率合成器，时钟发生器，扇出配送 |
| PLL： | 是 |
| 输入： | CMOS，TTL，晶体 |
| 输出： | CMOS，PECL |
| 电路数： | 1 |
| 比率 - 输入:输出： | 1:3 |
| 差分 - 输入:输出： | 无/是 |
| 频率 - 最大： | 260MHz |
| 除法器/乘法器： | 是/是 |
| 电源电压： | 4.75 V ~ 5.25 V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 16-SOIC |
| 包装： | 带卷 (TR) |
| 其它名称： | 1562BM-201-4LFT |
Pipeline Delay Reset Function
The ICS1562B implements the clocking sequence required to
reset the pipeline delay on Brooktree RAMDACs when the
LOAD output is programmed for a modulus of either 3, 4, 5,
6, 8 or 10. This sequence can be generated by setting the
appropriate register bit (DACRST) to a logic 1 and then reset-
ting to logic 0.
When changing frequencies, it is advisable to allow 500 mi-
croseconds after the new frequency is selected to activate the
reset function. The output frequency of the synthesizer should
be stable enough at that point for the video DAC to correctly
execute its reset sequence. See Figure 4 for a diagram of the
pipeline delay reset sequence.
Reference Oscillator and Crystal
Selection
The ICS1562B has circuitry on-board to implement a Pierce
oscillator with the addition of only one external component, a
quartz crystal. Pierce oscillators operate the crystal in anti-
(also called parallel-) resonant mode. See the AC Charac-
teristics for the effective capacitive loading to specify when
ordering crystals.
Series-resonant crystals may also be used with the ICS1562B.
Be aware that the oscillation frequency will be slightly higher
than the frequency that is stamped on the can (typically 0.025-
0.05%).
As the entire operation of the phase-locked loop depends on
having a stable reference frequency, we recommend that the
crystal be mounted as closely as possible to the package. Avoid
routing digital signals or the ICS1562B outputs underneath or
near these traces. It is also desirable to ground the crystal can
to the ground plane, if possible.
If an external reference frequency source is to be used with the
ICS1562B. it is important that it be jitter-free. The rising and
falling edges of that signal should be fast and free of noise for
best results.
The loop phase is locked to the falling edges of the XTAL1
input signals if the REFPOL bit is set to logic 0.
Internal Feedback
The ICS1562B supports LOAD (N1) and N2 divider
chains to act as the feedback divider for the PLL.
The N1 and N2 divider chains allow a much larger modulus to
be achieved than the PLL’s own feedback divider. Additionally,
the output of the N2 counter is accessible off-chip for perform-
ing horizontal reset of the graphics system, where necessary.
This mode is set under register control (ALTLOOP bit). The
reference divider (R counter) will ordinarily be set to divide by
1 in this mode, and the reference input will be supplied to
the XTAL1 input. The output frequency of the synthesizer
will then be:
F(CLK) : = F (XTAL1) . N1 . N2.
By using the phase-detector hardware disable mode, the PLL
can be made to free-run at the beginning of the vertical interval
of the external video, and can be reactivated at its completion.
ICS1562B-001 The ICS1562B-001 supports phase detector
disable via a special control mode. When the
PDRSTEN (phase detector reset enable) bit is
set and the last address latched is 15 (0Fh), a
high level on AD3 will disable PLL locking.
ICS1562B-201 The ICS1562B-201 supports phase detector
disable via the BLANK pin. When the
PDRSTEN bit is set, a high level on the
BLANK input will disable PLL locking.
Pipeline Delay Reset Timing
STROBE
or
DATCLK
CLK+
LOAD
10
9
11
12
TCLK
Figure 4
ICS1562B
4
相关PDF资料 |
PDF描述 |
|---|---|
| ICS843002AKI-40LFT | IC SYNTHESIZER LVPECL 32-VFQFPN |
| VI-BND-MV-F4 | CONVERTER MOD DC/DC 85V 150W |
| VI-BND-MV-F3 | CONVERTER MOD DC/DC 85V 150W |
| VI-BND-MV-F1 | CONVERTER MOD DC/DC 85V 150W |
| MS3454W16-9SW | CONN RCPT 4POS JAM NUT W/SCKT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL28005FH50Z-T7A | 功能描述:放大器 IC 开发工具 ISL28005FH50Z MICROP WR CUR SENSE AMP W/ RoHS:否 制造商:International Rectifier 产品:Demonstration Boards 类型:Power Amplifiers 工具用于评估:IR4302 工作电源电压:13 V to 23 V |
| ISL28006 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Micropower, Rail to Rail Input Current Sense Amplifier |
| ISL28006_10 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Micropower, Rail to Rail Input Current Sense Amplifier with Voltage Output |
| ISL28006_11 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Micropower, Rail to Rail Input Current Sense Amplifier |
| ISL28006FH-100EVAL1Z | 功能描述:放大器 IC 开发工具 ISL28006FH EVALRD 1 5LD GAIN OF 100 RoHS:否 制造商:International Rectifier 产品:Demonstration Boards 类型:Power Amplifiers 工具用于评估:IR4302 工作电源电压:13 V to 23 V |
发布紧急采购，3分钟左右您将得到回复。