- 您现在的位置：买卖IC网 > PDF目录383144 > ISL6292-2CR4Z (INTERSIL CORP) Dual Positive-Edge-Triggered D-Type Flip-Flops With Clear and Preset 14-SOIC -40 to 85 PDF资料下载
参数资料
| 型号： | ISL6292-2CR4Z |
| 厂商： | INTERSIL CORP |
| 元件分类： | 电源管理 |
| 英文描述： | Dual Positive-Edge-Triggered D-Type Flip-Flops With Clear and Preset 14-SOIC -40 to 85 |
| 中文描述： | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC16 |
| 封装： | 4 X 4 MM, ROHS COMPLIANT, PLASTIC, MO-220VGGC, QFN-16 |
| 文件页数： | 13/19页 |
| 文件大小： | 647K |
| 代理商： | ISL6292-2CR4Z |
13
FN9105.6
July 25, 2005
As the TEMP pin voltage rises from low and exceeds the
1.4V threshold, the under temperature signal rises and does
not clear until the TEMP pin voltage falls below the 1.2V
falling threshold. Similarly, the over-temperature signal is
given when the TEMP pin voltage falls below the 0.35V
threshold and does not clear until the voltage rises above
0.406V. The actual accuracy of the 2.8V is
not important
because all the thresholds and the TEMP pin voltage are
ratios determined by the resistor dividers, as shown in
Figure 22.
The NTC thermistor is required to have a resistance ratio of
7:1 at the low and the high temperature limits, that is,
(EQ. 7)
This is because at the low temperature limit, the TEMP pin
voltage is 1.4V, which is 1/2 of the 2.8V bias. Thus,
(EQ. 8)
where R
U
is the pull-up resistor as shown in Figure 22. On
the other hand, at the high temperature limit the TEMP pin
voltage is 0.35V, 1/8 of the 2.8V bias. Therefore,
(EQ. 9)
Various NTC thermistors are available for this application.
Table 1 shows the resistance ratio and the negative
temperature coefficient of the curve-1 NTC thermistor from
Vishay (http://www.vishay.com) at various temperatures. The
resistance at 3°C is approximately seven times the
resistance at 47°C, that is:
(EQ. 10)
Therefore, if 3°C is the low temperature limit, then the high
temperature limit is approximately 47°C. The pull-up resistor
R
U
can choose the same value as the resistance at 3°C.
The temperature hysteresis can be estimated. At the low
temperature, the hysteresis is approximately,
(EQ. 11)
where 0.051 is the NTC at 3°C. Similarly, the high
temperature hysteresis is,
(EQ. 12)
where the 0.039 is the NTC at 47°C.
For applications that do not need to monitor the battery
temperature, the NTC thermistor can be replaced with a
regular resistor of
a half value of the pull up resistor
R
U
.
Another option is to connect the TEMP pin to the IREF pin
that has a 0.8V output. With such connection, the IREF pin
can no longer be programmed with logic inputs.
Battery Removal Detection
The ISL6292 assumes that the thermistor is co-packed with
the battery and is removed together with the battery. When
the charger senses a TEMP pin voltage that is 2.1V or
higher, it assumes that the battery is removed. The battery
removal detection circuit is also shown in Figure 22. When a
battery is removed, a FAULT signal is indicated and charging
is halted. When a battery is inserted again, a new charge
cycle starts.
Indications
The ISL6292 has three indications: the input presence, the
charge status, and the fault indication. The input presence is
indicated by the V2P8 pin while the other two indications are
presented by the STATUS pin and FAULT pin respectively.
Figure 23 shows the V2P8 pin voltage vs. the input voltage.
Table 2 summarizes the other two pins.
TABLE 1. RESISTANCE RATIO OF VISHAY’S CURVE-1 NTC
TEMPERATURE (°C)
R
T
/R
25°C
NTC (%/°C)
0
3.266
5.1
3
2.806
5.1
5
2.540
5.0
25
1.000
4.4
45
0.4368
4.0
47
0.4041
3.9
50
0.3602
3.9
R
HOT
-------------------
7
=
R
COLD
R
U
=
R
HOT
R
U
7
-------
=
R
-----------------
R
47oC
7
=
T
hysLOW
1.4V 0.051
-------------------------------
3
≈
≈
oC
(
)
T
hysHIGH
-------------------------------------
4
≈
≈
oC
(
)
FIGURE 23. THE V2P8 PIN OUTPUT vs THE INPUT VOLTAGE
AT THE VIN PIN. VERTICAL: 1V/DIV,
HORIZONTAL: 100ms/DIV.
3.4V
2.4V
2.8V
V
IN
V2P8
ISL6292
相关PDF资料 |
PDF描述 |
|---|---|
| ISL6292-2CR5 | Li-ion/Li Polymer Battery Charger |
| ISL6292-2CR5-T | Dual Positive-Edge-Triggered D-Type Flip-Flops With Clear and Preset 14-SSOP -40 to 85 |
| ISL6292-2CR5Z | Dual Positive-Edge-Triggered D-Type Flip-Flops With Clear and Preset 14-SSOP -40 to 85 |
| ISL6292 | Li-ion/Li Polymer Battery Charger |
| ISL6292-1CR3Z | Octal D-Type Edge-Triggered Flip-Flops with 3-State Outputs 20-PDIP -40 to 85 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6292-2CR4Z-T | 功能描述:电池管理 LD VER OF ISL6292-2CR4-T RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| ISL6292-2CR5 | 功能描述:IC BATT CHRGR LI-ION 4.2V 16-QFN RoHS:否 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:1 系列:- 功能:充电管理 电池化学:锂离子（Li-Ion）、锂聚合物（Li-Pol） 电源电压:3.75 V ~ 6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SC-74A，SOT-753 供应商设备封装:SOT-23-5 包装:剪切带 (CT) 产品目录页面:669 (CN2011-ZH PDF) 其它名称:MCP73831T-2ACI/OTCT |
| ISL6292-2CR5-T | 功能描述:IC BATT CHRGR LI-ION 4.2V 16-QFN RoHS:否 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:1 系列:- 功能:充电管理 电池化学:锂离子（Li-Ion）、锂聚合物（Li-Pol） 电源电压:3.75 V ~ 6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SC-74A，SOT-753 供应商设备封装:SOT-23-5 包装:剪切带 (CT) 产品目录页面:669 (CN2011-ZH PDF) 其它名称:MCP73831T-2ACI/OTCT |
| ISL6292-2CR5Z | 功能描述:电池管理 LD VER OF ISL6292-2CR5 RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| ISL6292-2CR5Z-T | 功能描述:电池管理 LD VER OF ISL6292-2CR5-T RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。