- 您现在的位置：买卖IC网 > PDF目录30718 > LA4558 2.4 W, 2 CHANNEL, AUDIO AMPLIFIER, PDIP12 PDF资料下载
参数资料
| 型号： | LA4558 |
| 元件分类： | 音频／视频放大 |
| 英文描述： | 2.4 W, 2 CHANNEL, AUDIO AMPLIFIER, PDIP12 |
| 封装： | DIP-12 |
| 文件页数： | 4/9页 |
| 文件大小： | 321K |
| 代理商： | LA4558 |
LA4558
No.2088–4/9
Application Circuits
Voltage gain adjust
Stereo mode
The voltage gain is determined by on-chip resistor R1 (R2) and external feedback resistor RNF as follows :
Any voltage gain can be obtained by external
resistor RNf.
Bridge amplifier mode
The CH1 is a noninverting amplifer and the CH2 is an inverting amplifier. The total voltage gain, being apparently
higher than that of the CH1 by 6dB, is approximately calculated by the following formura.
VG=20log R2/R1+6 (dB)
To reduce the voltage gain, Rf is connected and the following formura is used.
VG=20log R2/Rf=R1+6 (dB)
Proper cares in using LA4558-applied set
1. Slider contact noise of variable resistor
Since the input circuit uses PNP transistors, no input coupling capacitor is required. However, if slider contact noise
of the variable resistor presents any problem, connect a capacitor in series with input.
2. Pop noise
If pop noise generated at the time of power ON/OFF disturbs you, connect a resistor of 500
to 1k across the
middle point and GND.
Thermal Design
Since the DIP-12F package is such that the Cu-foiled area of the printed circuit board is used to dissipate heat, make the
Cu-foiled area in the vicinity of the heat sink of the IC as large as possible when designing the printed circuit board.
Power dissipation Pd is increased depending on the supply voltage and load. So, it is recommended to use the printed
circuit board together with the heat sink. The following is a formula to be used to calculate Pd (for stereo use). For AC
power supply, however, it is recommended to actually measure Pd on the transformer of each set. For bridge amplifier
use, Pd is calculated at 1/2 of the load.
VG=20 log
[dB]
R1
RNF+R2
相关PDF资料 |
PDF描述 |
|---|---|
| LA4571MB | 0.032 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO20 |
| LA4571MB | 0.032 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO20 |
| LA4575 | 0.038 W, 2 CHANNEL, AUDIO AMPLIFIER, PDIP16 |
| LA4575M | 0.038 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO16 |
| LA4580M | 0.04 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO20 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LA4560M | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Analog IC |
| LA4570 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Analog IC |
| LA4570M | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Analog IC |
| LA4571 | 制造商:未知厂家 制造商全称:未知厂家 功能描述: |
| LA4571MB | 制造商:SANYO 制造商全称:Sanyo Semicon Device 功能描述:Low-Voltage Headphone Amplifier for Stereo Audio |
发布紧急采购，3分钟左右您将得到回复。