参数资料
| 型号： | X40411V8-BT1 |
| 厂商： | Intersil |
| 文件页数： | 10/24页 |
| 文件大小： | 0K |
| 描述： | IC VOLTAGE MON DUAL W/SUP 8TSSOP |
| 标准包装： | 2,500 |
| 类型： | 多压监控器 |
| 监视电压数目： | 2 |
| 输出： | 开路漏极或开路集电极 |
| 复位： | 高有效 |
| 复位超时： | 可调节/可选择 |
| 电压 - 阀值： | 2.6V，4.4V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 8-TSSOP |
| 包装： | 带卷 (TR) |
X40410, X40411, X40414, X40415
Figure 9. Byte Write Sequence
Signals from
the Master
S
t
a
r
t
Slave
Address
Byte
Address
Data
S
t
o
p
SDA Bus
0
Signals from
the Slave
A
C
K
A
C
K
A
C
K
Page Write
The device is capable of a page write operation. It is
initiated in the same manner as the byte write opera-
tion; but instead of terminating the write cycle after the
first data byte is transferred, the master can transmit
an unlimited number of 8-bit bytes. After the receipt of
each byte, the device will respond with an acknowl-
edge, and the address is internally incremented by
one. The page address remains constant. When the
counter reaches the end of the page, it “rolls over” and
goes back to ‘0’ on the same page.
Figure 10. Page Write Operation
This means that the master can write 16 bytes to the
page starting at any location on that page. If the master
begins writing at location 10, and loads 12 bytes, then
the first 6 bytes are written to locations 10 through 15,
and the last 6 bytes are written to locations 0 through 5.
Afterwards, the address counter would point to location
6 of the page that was just written. If the master sup-
plies more than 16 bytes of data, then new data over-
writes the previous data, one byte at a time.
Signals from
the Master
S
t
a
r
t
Slave
Address
Byte
Address
Data
(1)
(1 ≤ n ≤ 16)
Data
(n)
S
t
o
p
SDA Bus
1 0 1 0 0 0
0
Signals from
the Slave
A
C
K
A
C
K
A
C
K
A
C
K
Figure 11. Writing 12 bytes to a 16-byte page starting at location 10.
7 Bytes
5 Bytes
address
=6
address pointer
ends here
Addr = 7
address
10
address
n-1
The master terminates the Data Byte loading by issuing
a stop condition, which causes the device to begin the
nonvolatile write cycle. As with the byte write operation,
10
all inputs are disabled until completion of the internal
write cycle. See Figure 10 for the address, acknowl-
edge, and data transfer sequence.
FN8116.0
March 28, 2005
相关PDF资料 |
PDF描述 |
|---|---|
| MAX881REUB+T | IC SUPPLY BIAS LN 10-UMAX |
| GBM43DTKT | CONN EDGECARD 86POS DIP .156 SLD |
| X40411V8-B | IC VOLTAGE MON DUAL W/SUP 8TSSOP |
| MAX845EUA+T | IC DRVR TRANSF ISO 8-UMAX |
| UUP1V3R3MCL1GS | CAP ALUM 3.3UF 35V 20% SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LPC1343FBD48151 | 制造商:NXP Semiconductors 功能描述:IC 32BIT MCU ARM 72MHZ LQFP-48 |
| LPC1343FHN33 | 制造商:NXP Semiconductors 功能描述:MCU 32BIT 32KFLASH CORTEX-M3 33HVQFN 制造商:NXP Semiconductors 功能描述:MCU, 32BIT, 32KFLASH, CORTEX-M3, 33HVQFN |
| LPC1343FHN33,518 | 功能描述:ARM微控制器 - MCU 32KB Flash, 3.6V RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 处理器系列:STM32F373xx 数据总线宽度:32 bit 最大时钟频率:72 MHz 程序存储器大小:256 KB 数据 RAM 大小:32 KB 片上 ADC:Yes 工作电源电压:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:LQFP-48 安装风格:SMD/SMT |
| LPC1343FHN33,551 | 功能描述:ARM微控制器 - MCU 32-bit ARM Cortex-M3 32kb Flash RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 处理器系列:STM32F373xx 数据总线宽度:32 bit 最大时钟频率:72 MHz 程序存储器大小:256 KB 数据 RAM 大小:32 KB 片上 ADC:Yes 工作电源电压:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:LQFP-48 安装风格:SMD/SMT |
| LPC1343FHN33551 | 制造商:NXP Semiconductors 功能描述:MCU 32BIT CORTEX M3 33HVQFN |
发布紧急采购，3分钟左右您将得到回复。