- 您现在的位置：买卖IC网 > PDF目录377678 > LT1082M (Linear Technology Corporation) Parallel-Load 8-Bit Serial Shift Registers 16-SSOP 0 to 70 PDF资料下载
参数资料
| 型号： | LT1082M |
| 厂商： | Linear Technology Corporation |
| 英文描述： | Parallel-Load 8-Bit Serial Shift Registers 16-SSOP 0 to 70 |
| 中文描述： | 1A条高电压，效率开关稳压器 |
| 文件页数： | 8/12页 |
| 文件大小： | 250K |
| 代理商： | LT1082M |
8
LT1082
OPERATIOU
disconnect the main error amplifier output and connects
the output of the flyback amplifier to the comparator input.
The LT1082 will then regulate the value of the flyback pulse
with respect to the supply voltage. This flyback pulse is
directly proportional to output voltage in the traditional
transformer coupled flyback topology regulator. By
regulating the amplitude of the flyback pulse, the output
voltage can be regulated with no direct connection between
input and output. The output is fully floating up to the
breakdown voltage of the transformer windings. Multiple
floating outputs are easily obtained with additional
windings. A special delay network inside the LT1082
ignores the leakage inductance spike at the leading edge of
the flyback pulse to improve output regulation.
When I
FB
drawn out of the FB pin reaches 350
μ
A, the
LT1082 shifts the switching frequency down to 12kHz.
This unique feature provides high voltage short-circuit
protection in systems like the telecom 5V supplies with
input voltages down to –70V; lower frequency is needed
under short-circuit conditions with current mode switchers
because minimum “on” time cannot be forced below the
internally set blanking time. Referring to the telecom 5V
supply circuit on the front page, with output shorted to
ground, the V
FB
stays at 0.6V when sourcing I
FB
up to
1mA. If the FB pin is forced to source more than 1mA, the
frequency shifting function may be defeated. Therefore,
the minimum suggested value for R
FB
is 1k and the
maximum suggested value is 1.2k. Also, no capacitance
more than 1nF should be used on the FB pin, because it
may cause unstable switching frequency in this low
frequency mode.
The error signal developed at the comparator input is
brought out externally. This pin (V
C
) has four different
functions. It is used for frequency compensation, current
limit adjustment, soft starting, and total regulator shutdown.
During normal regulator operation this pin sits at a voltage
between 0.9V (low output current) and 2V (high output
current). The error amplifiers are current output (g
m
)
types, so this voltage can be externally clamped for
adjusting current limit. Likewise, a capacitor-coupled
external clamp will provide soft start. Switch duty cycle
goes to zero if the V
C
pin is pulled to ground through a
diode, placing the LT1082 in an idle mode. Pulling the V
C
pin below 0.15V causes total regulator shutdown, with
only 120
μ
A supply current for shutdown circuitry biasing.
See AN19 for full application details.
Extra Pins on the MiniDIP Packages
The miniDIP LT1082 has the emitters of the power
transistor brought out separately from the ground pin.
This eliminates errors due to ground pin voltage drops and
allows the user to reduce switch current limit by a factor
of 2:1 by leaving the second emitter (E2) disconnected.
The first emitter (E1) should always be connected to the
ground pin. Note that switch “on” resistance doubles
when E2 is left open, so efficiency will suffer somewhat
when switch currents exceed 100mA. Also, note that chip
dissipation will actually increasewith E2 open during
normal load operation, even though dissipation in current
limit mode will decrease See “Thermal Considerations.”
Thermal Considerations When Using the
MiniDIP Packages
The low supply current and high switch efficiency of the
LT1082 allow it to be used without a heat sink in most
applications when the TO-220 package is selected.
This package is rated at 50
°
C/W. The miniDIPs, however,
are rated at 100
°
C/W in ceramic (J) and 90
°
/W in plastic
(N).
Care should be taken for miniDIP applications to ensure
that the worst case input voltage and load current conditions
do not cause excessive die temperatures. The following
formulas can be used as a rough guide to calculate LT1082
power dissipation. For more details, the reader is referred
to Application Note 19 (AN19), “Efficiency Calculations”
section.
Average supply current (including driver current) is:
I
IN
≈
4.5mA + I
SW
(0.004 + DC/28)
I
SW
= switch current
DC = switch duty cycle
Switch power dissipation is given by:
P
SW
= (I
SW
)
2
R
SW
DC
R
SW
= LT1082 switch “on” resistance (1.2
maximum)
相关PDF资料 |
PDF描述 |
|---|---|
| LT1082IN8 | 1A High Voltage, Efficiency Switching Voltage Regulator |
| LT1083CP-12 | 3A, 5A, 7.5A Low Dropout Positive Fixed Regulators |
| LT1084-3.3 | TV 30C 30MIX SKT PLUG RECP |
| LT1083CK-12 | 3A, 5A, 7.5A Low Dropout Positive Fixed Regulators |
| LT1083CK-5 | 3A, 5A, 7.5A Low Dropout Positive Fixed Regulators |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT1082MJ8 | 制造商:Linear Technology 功能描述:Conv DC-DC Single Non-Inv/Inv/Step Up/Step Down 3V to 75V 8-Pin CDIP |
| LT1083CK-12 | 制造商:Linear Technology 功能描述:LDO Regulator Pos 12V 7.5A 3-Pin(2+Tab) TO-3 |
| LT1083CP | 功能描述:IC REG LDO ADJ 7.5A TO-3P-3 RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:3,000 系列:- 稳压器拓扑结构:正，固定式 输出电压:2.5V 输入电压:2.5 V ~ 5.5 V 电压 - 压降（标准）:- 稳压器数量:1 电流 - 输出:300mA（最小值） 电流 - 限制（最小）:360mA 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 供应商设备封装:TSOT-23-5 包装:带卷 (TR) |
| LT1083CP#PBF | 功能描述:IC REG LDO ADJ 7.5A TO-3P-3 RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:3,000 系列:- 稳压器拓扑结构:正，固定式 输出电压:2.5V 输入电压:2.5 V ~ 5.5 V 电压 - 压降（标准）:- 稳压器数量:1 电流 - 输出:300mA（最小值） 电流 - 限制（最小）:360mA 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 供应商设备封装:TSOT-23-5 包装:带卷 (TR) |
| LT1083CP-12 | 功能描述:IC REG LDO 12V 7.5A TO-3P-3 RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:3,000 系列:- 稳压器拓扑结构:正，固定式 输出电压:2.5V 输入电压:2.5 V ~ 5.5 V 电压 - 压降（标准）:- 稳压器数量:1 电流 - 输出:300mA（最小值） 电流 - 限制（最小）:360mA 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 供应商设备封装:TSOT-23-5 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。