- 您现在的位置：买卖IC网 > PDF目录13935 > LTC3604IMSE#PBF (Linear Technology)IC REG BUCK SYNC 2.5A 16MSOP PDF资料下载
参数资料
| 型号： | LTC3604IMSE#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 15/24页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK SYNC 2.5A 16MSOP |
| 标准包装： | 37 |
| 类型： | 降压（降压） |
| 输出数： | 1 |
| 输入电压： | 3.6 V ~ 15 V |
| PWM 型： | 电流模式，混合 |
| 频率 - 开关： | 800kHz ~ 4MHz |
| 电流 - 输出： | 2.5A |
| 同步整流器： | 是 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-TFSOP（0.118"，3.00mm 宽）裸露焊盘 |
| 包装： | 管件 |
| 供应商设备封装： | 16-MSOP，裸露焊盘 |
LTC3604
APPLICATIONS INFORMATION
a soft-start function by connecting a capacitor from the
TRACK/SS pin to ground. The relationship between output
rise time and TRACK/SS capacitance is given by:
t SS = 430,000 × C TRACK/SS
A default internal soft-start timer forces a minimum soft-
PGOOD
VOLTAGE
NOMINAL OUTPUT
V OUT
start time of 400μs by overriding the TRACK/SS pin input
–8%
–5% 0%
5%
8%
3604 F04
during this time period. Hence, capacitance values less
than approximately 1000pF will not signi?cantly affect
soft-start behavior.
When using the TRACK/SS pin, the regulator defaults to
Burst Mode operation until the output exceeds 80% of
its ?nal value (V FB > 0.48V). Once the output reaches this
voltage, the operating mode of the regulator switches to
the mode selected by the MODE/SYNC pin as described
above. During normal operation, if the output drops below
10% of its ?nal value (as it may when tracking down, for
instance), the regulator will automatically switch to Burst
Mode operation to prevent inductor saturation and improve
TRACK/SS pin accuracy.
Output Power Good
The PGOOD output of the LTC3604 is driven by a 15Ω
(typical) open-drain pull-down device. This device will
be turned off once the output voltage is within ±5% (typi-
cal) of the target regulation point allowing the voltage at
PGOOD to rise via an external pull-up resistor (100k typi-
cal). If the output voltage exits a ±8% (typical) regulation
window around the target regulation point the open-drain
output will pull down with 15Ω output resistance to
ground, thus dropping the PGOOD pin voltage. A ?lter
time of 40μs (typical) acts to prevent unwanted PGOOD
output changes during V OUT transient events. As a result,
the output voltage must be within the target regulation
window of ±5% for 40μs before the PGOOD pin is pulled
high. Conversely, the output voltage must exit the ±8%
regulation window for 40μs before the PGOOD pin pulls
to ground (see Figure 4).
Ef?ciency Considerations
The percent ef?ciency of a switching regulator is equal to
the output power divided by the input power times 100%.
Figure 4. PGOOD Pin Behavior
It is often useful to analyze individual losses to determine
what is limiting the ef?ciency and which change would
produce the most improvement. Percent ef?ciency can
be expressed as:
% Ef?ciency = 100% – (L1 + L2 + L3 +…)
where L1, L2, etc. are the individual loss terms as a per-
centage of input power.
Although all dissipative elements in the circuit produce
losses, three main sources account for the majority of the
losses in the LTC3604: 1) I 2 R loss, 2) switching losses
and quiescent current loss, 3) transition losses and other
system losses.
1. I 2 R loss is calculated from the DC resistances of the
internal switches, R SW , and external inductor, R L . In
continuous mode, the average output current will
?ow through inductor L but is “chopped” between the
internal top and bottom power MOSFETs. Thus, the
series resistance looking into the SW pin is a function
of both the top and bottom MOSFET’s R DS(ON) and the
duty cycle (DC) as follows:
R SW = (R DS(ON)TOP )(DC) + (R DS(ON)BOT )(1 – DC)
The R DS(ON) for both the top and bottom MOSFETs can be
obtained from the Typical Performance Characteristics
curves. Thus to obtain I 2 R loss:
“I 2 R LOSS” = I OUT2 · (R SW + R L )
2. The internal LDO supplies the power to the INTV CC rail.
The total power loss here is the sum of the switching
losses and quiescent current losses from the control
circuitry.
3604f
15
相关PDF资料 |
PDF描述 |
|---|---|
| LT3695IMSE-5#PBF | IC REG BUCK 5V 1A 16MSOP |
| 16ML68MEFC6.3X5 | CAP ALUM 68UF 16V 20% RADIAL |
| 10ML120MEFC6.3X7 | CAP ALUM 120UF 10V 20% RADIAL |
| 6.3NA100MEFC5X11 | CAP ALUM 100UF 6.3V 20% BI-P RAD |
| ECC19DRXS-S734 | CONN EDGECARD 38POS DIP .100 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3604IUD#PBF | 功能描述:IC REG BUCK SYNC 2.5A 16QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LTC3604IUD#TRPBF | 功能描述:IC REG BUCK SYNC 2.5A 16QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LTC3605AEUF#PBF | 功能描述:IC REG BUCK SYNC ADJ 5A 24QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LTC3605AEUF#TRPBF | 功能描述:IC REG BUCK SYNC ADJ 5A 24QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LTC3605AIUF#PBF | 功能描述:IC REG BUCK SYNC ADJ 5A 24QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
发布紧急采购，3分钟左右您将得到回复。