参数资料
型号: M25PE10-VMN6P
厂商: 意法半导体
元件分类: DRAM
英文描述: 4 Mbit Uniform Sector, Serial Flash Memory
中文描述: 4兆位统一部门,串行闪存
文件页数: 29/60页
文件大小: 310K
代理商: M25PE10-VMN6P
M25PE20, M25PE10
Instructions
29/60
Table 10.
The protection features of the device are summarized in
Table 10
.
When the Status Register Write Disable (SRWD) bit of the Status Register is 0 (its initial
delivery state), it is possible to write to the Status Register provided that the Write Enable
Latch (WEL) bit has previously been set by a Write Enable (WREN) instruction, regardless
of the whether Write Protect (W) is driven High or Low.
When the Status Register Write Disable (SRWD) bit of the Status Register is set to 1, two
cases need to be considered, depending on the state of Write Protect (W):
If Write Protect (W) is driven High, it is possible to write to the Status Register provided
that the Write Enable Latch (WEL) bit has previously been set by a Write Enable
(WREN) instruction.
If Write Protect (W) is driven Low, it is
not
possible to write to the Status Register
even
if the Write Enable Latch (WEL) bit has previously been set by a Write Enable (WREN)
instruction. (Attempts to write to the Status Register are rejected, and are not accepted
for execution). As a consequence, all the data bytes in the memory area that are
software protected (SPM2) by the Block Protect (BP1, BP0) bits of the Status Register,
are also hardware protected against data modification.
Regardless of the order of the two events, the Hardware Protected Mode (HPM) can be
entered:
by setting the Status Register Write Disable (SRWD) bit after driving Write Protect (W)
Low
or by driving Write Protect (W) Low after setting the Status Register Write Disable
(SRWD) bit.
The only way to exit the Hardware Protected Mode (HPM) once entered is to pull Write
Protect (W) High.
If Write Protect (W) is permanently tied High, the Hardware Protected Mode (HPM) can
never be activated, and only the Software Protected Mode (SPM2), using the Block Protect
(BP1, BP0) bits of the Status Register, can be used.
Protection modes (T9HX process only, see
Important note on page 6
)
W
Signal
SRWD
Bit
Mode
Write Protection of the
Status Register
Memory Content
Protected Area
(1)
1.
As defined by the values in the Block Protect (BP1, BP0) bits of the Status Register, as shown in
Table 3
.
Unprotected Area
(1)
1
0
Second
Software
Protected
(SPM2)
Status Register is Writable
(if the WREN instruction
has set the WEL bit)
The values in the SRWD,
BP1 and BP0 bits can be
changed
Protected against
Page Program,
Sector Erase and
Bulk Erase
Ready to accept
Page Program and
Sector Erase
instructions
0
0
1
1
0
1
Hardware
Protected
(HPM)
Status Register is
Hardware write protected
The values in the SRWD,
BP1 and BP0 bits cannot
be changed
Protected against
Page Program,
Sector Erase and
Bulk Erase
Ready to accept
Page Program and
Sector Erase
instructions
相关PDF资料
PDF描述
M25PE10-VMP6G 4 Mbit Uniform Sector, Serial Flash Memory
M25PE10-VMP6P 4 Mbit Uniform Sector, Serial Flash Memory
M25PE10-VMP6TG 4 Mbit Uniform Sector, Serial Flash Memory
M25PE10-VMP6TP 4 Mbit Uniform Sector, Serial Flash Memory
M25PE20_07 4 Mbit Uniform Sector, Serial Flash Memory
相关代理商/技术参数
参数描述
M25PE10-VMN6TG 制造商:NUMONYX 制造商全称:Numonyx B.V 功能描述:1 and 2 Mbit, page-erasable serial Flash memories with byte alterability, 75 MHz SPI bus, standard pinout
M25PE10-VMN6TP 功能描述:电可擦除可编程只读存储器 SERIAL PAGE ERASE FLASH 1 Mbit Datas RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8
M25PE10-VMN6TPBA 制造商:Micron Technology Inc 功能描述:SERIAL NOR 制造商:Micron Technology Inc 功能描述:NOR Flash Serial-SPI 3V/3.3V 1Mbit 128K x 8bit 8ns T/R 制造商:Micron Technology Inc 功能描述:AUTOMOTIVE - Tape and Reel
M25PE10-VMN6TPBA TR 制造商:Micron Technology Inc 功能描述:IC FLASH 1MBIT 75MHZ 8SO
M25PE10-VMP6G 制造商:Micron Technology Inc 功能描述:FLASH SERL-SPI 3.3V 1MBIT 128KX8 8NS 8PIN VDFPN EP - Trays 制造商:Micron Technology Inc 功能描述:IC FLASH 1MBIT 75MHZ 8VFQFPN