- 您现在的位置：买卖IC网 > PDF目录377802 > M25PE10-VMN6P (意法半导体) 4 Mbit Uniform Sector, Serial Flash Memory PDF资料下载
参数资料
| 型号： | M25PE10-VMN6P |
| 厂商： | 意法半导体 |
| 元件分类： | DRAM |
| 英文描述： | 4 Mbit Uniform Sector, Serial Flash Memory |
| 中文描述： | 4兆位统一部门，串行闪存 |
| 文件页数： | 40/60页 |
| 文件大小： | 310K |
| 代理商： | M25PE10-VMN6P |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页当前第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页
Instructions
M25PE20, M25PE10
40/60
6.14
Sector Erase (SE)
The Sector Erase (SE) instruction sets to 1 (FFh) all bits inside the chosen sector. Before it
can be accepted, a Write Enable (WREN) instruction must previously have been executed.
After the Write Enable (WREN) instruction has been decoded, the device sets the Write
Enable Latch (WEL).
The Sector Erase (SE) instruction is entered by driving Chip Select (S) Low, followed by the
instruction code, and three address Bytes on Serial Data Input (D). Any address inside the
Sector (see
Table 5
or
Table 6
) is a valid address for the Sector Erase (SE) instruction. Chip
Select (S) must be driven Low for the entire duration of the sequence.
The instruction sequence is shown in
Figure 21
.
Chip Select (S) must be driven High after the eighth bit of the last address Byte has been
latched in, otherwise the Sector Erase (SE) instruction is not executed. As soon as Chip
Select (S) is driven High, the self-timed Sector Erase cycle (whose duration is t
SE
) is
initiated. While the Sector Erase cycle is in progress, the Status Register may be read to
check the value of the Write In Progress (WIP) bit. The Write In Progress (WIP) bit is 1
during the self-timed Sector Erase cycle, and is 0 when it is completed. At some unspecified
time before the cycle is complete, the Write Enable Latch (WEL) bit is reset.
A Sector Erase (SE) instruction applied to a sector that contains a page that is Hardware
Protected is not executed.
Any Sector Erase (SE) instruction, while an Erase, Program or Write cycle is in progress, is
rejected without having any effects on the cycle that is in progress.
Figure 21.
Sector Erase (SE)
instruction sequence
1.
Address bits A23 to A18 are Don’t Care in the M25PE20. Address bits A23 to A17 are Don’t Care in the
M25PE10.
24 Bit Address
C
D
AI03751D
S
2
1
3
4
5
6
7
8
9
29 30 31
Instruction
0
23 22
2
0
1
MSB
相关PDF资料 |
PDF描述 |
|---|---|
| M25PE10-VMP6G | 4 Mbit Uniform Sector, Serial Flash Memory |
| M25PE10-VMP6P | 4 Mbit Uniform Sector, Serial Flash Memory |
| M25PE10-VMP6TG | 4 Mbit Uniform Sector, Serial Flash Memory |
| M25PE10-VMP6TP | 4 Mbit Uniform Sector, Serial Flash Memory |
| M25PE20_07 | 4 Mbit Uniform Sector, Serial Flash Memory |
相关代理商/技术参数 |
参数描述 |
|---|---|
| M25PE10-VMN6TG | 制造商:NUMONYX 制造商全称:Numonyx B.V 功能描述:1 and 2 Mbit, page-erasable serial Flash memories with byte alterability, 75 MHz SPI bus, standard pinout |
| M25PE10-VMN6TP | 功能描述:电可擦除可编程只读存储器 SERIAL PAGE ERASE FLASH 1 Mbit Datas RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 |
| M25PE10-VMN6TPBA | 制造商:Micron Technology Inc 功能描述:SERIAL NOR 制造商:Micron Technology Inc 功能描述:NOR Flash Serial-SPI 3V/3.3V 1Mbit 128K x 8bit 8ns T/R 制造商:Micron Technology Inc 功能描述:AUTOMOTIVE - Tape and Reel |
| M25PE10-VMN6TPBA TR | 制造商:Micron Technology Inc 功能描述:IC FLASH 1MBIT 75MHZ 8SO |
| M25PE10-VMP6G | 制造商:Micron Technology Inc 功能描述:FLASH SERL-SPI 3.3V 1MBIT 128KX8 8NS 8PIN VDFPN EP - Trays 制造商:Micron Technology Inc 功能描述:IC FLASH 1MBIT 75MHZ 8VFQFPN |
发布紧急采购，3分钟左右您将得到回复。