- 您现在的位置：买卖IC网 > PDF目录180125 > M29F400FB55M3F2 256K X 16 FLASH 5V PROM, 55 ns, PDSO44 PDF资料下载
参数资料
| 型号： | M29F400FB55M3F2 |
| 元件分类： | PROM |
| 英文描述： | 256K X 16 FLASH 5V PROM, 55 ns, PDSO44 |
| 封装： | 0.500 INCH, ROHS COMPLIANT, PLASTIC, SOP-44 |
| 文件页数： | 19/65页 |
| 文件大小： | 1669K |
| 代理商： | M29F400FB55M3F2 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页当前第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页
Command Interface
M29FxxxFT, M29FxxxFB
26/65
During the program operation the memory will ignore all commands. It is not possible to
issue any command to abort or pause the operation. Typical program times are given in
Table Table 6.. Bus Read operations during the program operation will output the Status
Register on the Data Inputs/Outputs. See the section on the Status Register for more
details.
After the program operation has completed the memory returns to the Read mode, unless
an error has occurred. When an error occurs the memory continues to output the Status
Register. A Read/Reset command must be issued to reset the error condition and return to
Read mode.
Note that the Program command cannot change a bit set at ’0’ back to ’1’. One of the Erase
Commands must be used to set all the bits in a block or in the whole memory from ’0’ to ’1’.
4.4
Unlock Bypass Command.
The Unlock Bypass command is used in conjunction with the Unlock Bypass Program
command to program the memory. When the access time to the device is long (as with
some EPROM programmers) considerable time saving can be made by using these
commands. Three Bus Write operations are required to issue the Unlock Bypass command.
Once the Unlock Bypass command has been issued the memory will only accept the Unlock
Bypass Program command and the Unlock Bypass Reset command. The memory can be
read as if in Read mode.
4.5
Unlock Bypass Program Command.
The Unlock Bypass Program command can be used to program one address in memory at
a time. The command requires two Bus Write operations, the final write operation latches
the address and data, and starts the Program/Erase Controller.
The Program operation using the Unlock Bypass Program command behaves identically to
the Program operation using the Program command. A protected block cannot be
programmed; the operation cannot be aborted and the Status Register is read. Errors must
be reset using the Read/Reset command, which leaves the device in Unlock Bypass Mode.
See the Program command for details on the behavior.
4.6
Unlock Bypass Reset Command.
The Unlock Bypass Reset command can be used to return to Read/Reset mode from
Unlock Bypass Mode. Two Bus Write operations are required to issue the Unlock Bypass
Reset command. Read/Reset command does not exit from Unlock Bypass Mode.
4.7
Chip Erase Command.
The Chip Erase command can be used to erase the entire chip. Six Bus Write operations
are required to issue the Chip Erase Command and start the Program/Erase Controller.
If any blocks are protected then these are ignored and all the other blocks are erased. If all
of the blocks are protected the Chip Erase operation appears to start but will terminate
相关PDF资料 |
PDF描述 |
|---|---|
| M29F400FB5AN6F2 | 256K X 16 FLASH 5V PROM, 55 ns, PDSO48 |
| M29W800B-120N5RTR | 1M X 8 FLASH 3V PROM, 120 ns, PDSO48 |
| M29W800T-150M6 | 1M X 8 FLASH 3V PROM, 150 ns, PDSO44 |
| M29W800FB9N3F | 512K X 16 FLASH 3V PROM, 90 ns, PDSO48 |
| M2CT-90A1-24ER | PUSHBUTTON SWITCH, DPST, MOMENTARY, PANEL MOUNT-THREADED |
相关代理商/技术参数 |
参数描述 |
|---|---|
| M29F400FB55M3F2 TR | 制造商:Micron Technology Inc 功能描述:IC FLASH 4MBIT 55NS 44SO |
| M29F400FB55M3T2 | 制造商:Micron Technology Inc 功能描述:AUTOMOTIVE 5V - Trays |
| M29F400FB55N3E2 | 制造商:Micron Technology Inc 功能描述:AUTOMOTIVE 5V - Trays 制造商:Micron Technology Inc 功能描述:IC FLASH 4MBIT 55NS 48TSOP |
| M29F400FB55N3F2 | 制造商:Micron Technology Inc 功能描述:AUTOMOTIVE 5V - Tape and Reel |
| M29F400FB55N3F2 TR | 制造商:Micron Technology Inc 功能描述:IC FLASH 4MBIT 55NS 48TSOP |
发布紧急采购，3分钟左右您将得到回复。