- 您现在的位置：买卖IC网 > PDF目录370930 > M38270E3MXXXFP (Mitsubishi Electric Corporation) 16-Bit Buffer/Driver With 3-State Outputs 48-TVSOP -40 to 85 PDF资料下载
参数资料
| 型号： | M38270E3MXXXFP |
| 厂商： | Mitsubishi Electric Corporation |
| 英文描述： | 16-Bit Buffer/Driver With 3-State Outputs 48-TVSOP -40 to 85 |
| 中文描述： | 单芯片8位CMOS微机 |
| 文件页数： | 22/70页 |
| 文件大小： | 1112K |
| 代理商： | M38270E3MXXXFP |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页当前第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页
22
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
3827 Group
MITSUBISHI MICROCOMPUTERS
Timer X mode register
(TXM : address 0027
16
)
Timer X write control bit
0 : Write value in latch and counter
1 : Write value in latch only
Real time port control bit
0 : Real time port function invalid
1 : Real time port function valid
P5
2
data for real time port
P5
3
data for real time port
Timer X operating mode bits
b5 b4
0 0 : Timer mode
0 1 : Pulse output mode
1 0 : Event counter mode
1 1 : Pulse width measurement mode
CNTR
0
active edge switch bit
0 : Count at rising edge in event counter mode
Start from “H” output in pulse output mode
Measure “H” pulse width in pulse width
measurement mode
Falling edge active for CNTR
0
interrupt
1 : Count at falling edge in event counter mode
Start from “L” output in pulse output mode
Measure “L” pulse width in pulse width
measurement mode
Rising edge active for CNTR
0
interrupt
Timer X stop control bit
0 : Count start
1 : Count stop
b7
b0
Timer X
Timer X is a 16-bit timer that can be selected in one of four modes
and can be controlled the timer X write and the real time port by
setting the timer X mode register.
(1) Timer Mode
The timer counts f(X
IN
)/16 (or f(X
CIN
)/16 in low-speed mode).
(2) Pulse Output Mode
Each time the timer underflows, a signal output from the CNTR
0
pin is inverted. Except for this, the operation in pulse output mode
is the same as in timer mode. When using a timer in this mode, set
the port shared with the CNTR
0
pin to input.
(3) Event Counter Mode
The timer counts signals input through the CNTR
0
pin.
Except for this, the operation in event counter mode is the same
as in timer mode. When using a timer in this mode, set the port
shared with the CNTR
0
pin to input.
(4) Pulse Width Measurement Mode
The count source is f(X
IN
)/16 (or f(X
CIN
)/16 in low-speed mode). If
CNTR
0
active edge switch bit is “0”, the timer counts while the in-
put signal of CNTR
0
pin is at “H”. If it is “1”, the timer counts while
the input signal of CNTR
0
pin is at “L”. When using a timer in this
mode, set the port shared with tha CNTR
0
pin to input.
G
Timer X write control
If the timer X write control bit is “0”, when the value is written in the
address of timer X, the value is loaded in the timer X and the latch
at the same time.
If the timer X write control bit is “1”, when the value is written in the
address of timer X, the value is loaded only in the latch. The value
in the latch is loaded in timer X after timer X underflows.
If the value is written in latch only, unexpected value may be set in
the high-order counter when the writing in high-order latch and the
underflow of timer X are performed at the same timing.
I
Note on CNTR
0
interrupt active edge
selection
CNTR
0
interrupt active edge depends on the CNTR
0
active edge
switch bit.
G
Real time port control
While the real time port function is valid, data for the real time port
are output from ports P5
2
and P5
3
each time the timer X
underflows. (However, if the real time port control bit is changed
from “0” to “1”, data are output without the timer X.) When the data
for the real time port is changed while the real time port function is
valid, the changed data are output at the next underflow of timer X.
Before using this function, set the corresponding port direction
registers to output mode.
Fig. 18 Structure of timer X mode register
相关PDF资料 |
PDF描述 |
|---|---|
| M38270E3MXXXFS | 16-Bit Buffer/Driver With 3-State Outputs 56-BGA MICROSTAR JUNIOR -40 to 85 |
| M38270E3MXXXGP | 16-Bit Buffer/Driver With 3-State Outputs 56-BGA MICROSTAR JUNIOR -40 to 85 |
| M38270E3MXXXHP | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M38270E4MXXXFP | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M38270E4MXXXFS | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
相关代理商/技术参数 |
参数描述 |
|---|---|
| M3828 BK001 | 制造商:Alpha Wire Company 功能描述:CBL 3COND 16AWG BLK 1000' |
| M3828 BK002 | 制造商:Alpha Wire Company 功能描述:CBL 3COND 16AWG BLK 500' |
| M3828 BK005 | 制造商:Alpha Wire Company 功能描述:CBL 3COND 16AWG BLK 100' |
| M3828 BK199 | 制造商:Alpha Wire Company 功能描述:CBL 3COND 16AWG BLK 3000=3000' |
| M3829 BK001 | 制造商:Alpha Wire Company 功能描述:CBL 4COND 16AWG BLK 1000' |
发布紧急采购，3分钟左右您将得到回复。