参数资料
型号: M38270E3MXXXFP
厂商: Mitsubishi Electric Corporation
英文描述: 16-Bit Buffer/Driver With 3-State Outputs 48-TVSOP -40 to 85
中文描述: 单芯片8位CMOS微机
文件页数: 48/70页
文件大小: 1112K
代理商: M38270E3MXXXFP
48
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
3827 Group
MITSUBISHI MICROCOMPUTERS
NOTES ON PROGRAMMING
Processor Status Register
The contents of the processor status register (PS) after a reset are
undefined, except for the interrupt disable flag (I) which is “1”. Af-
ter a reset, initialize flags which affect program execution.
In particular, it is essential to initialize the index X mode (T) and
the decimal mode (D) flags because of their effect on calculations.
Interrupt
The contents of the interrupt request bits do not change immedi-
ately after they have been written. After writing to an interrupt
request register, execute at least one instruction before performing
a BBC or BBS instruction.
Decimal Calculations
To calculate in decimal notation, set the decimal mode flag (D)
to “1”, then execute an ADC or SBC instruction. After executing
an ADC or SBC instruction, execute at least one instruction be-
fore executing a SEC, CLC, or CLD instruction.
In decimal mode, the values of the negative (N), overflow (V),
and zero (Z) flags are invalid.
Timers
If a value n (between 0 and 255) is written to a timer latch, the fre-
quency division ratio is 1/(n + 1).
Multiplication and Division Instructions
The index mode (T) and the decimal mode (D) flags do not affect
the MUL and DIV instruction.
The execution of these instructions does not change the contents
of the processor status register.
Ports
The contents of the port direction registers cannot be read.
The following cannot be used:
The data transfer instruction (LDA, etc.)
The operation instruction when the index X mode flag (T) is “1”
The addressing mode which uses the value of a direction regis-
ter as an index
The bit-test instruction (BBC or BBS, etc.) to a direction register
The read-modify-write instruction (ROR, CLB, or SEB, etc.) to a
direction register
Use instructions such as LDM and STA, etc., to set the port direc-
tion registers.
Serial I/O
In clock synchronous serial I/O, if the receive side is using an ex-
ternal clock and it is to output the S
RDY
signal, set the transmit
enable bit, the receive enable bit, and the S
RDY
output enable bit
to “1”.
Serial I/O1 continues to output the final bit from the T
X
D pin after
transmission is completed.
In serial I/O2, the S
OUT2
pin goes to high impedance state after
transmission is completed.
A-D Converter
The comparator uses internal capacitors whose charge will be lost
if the clock frequency is too low.
Make sure that f(X
IN
) is at least 500 kHz during an A-D conver-
sion.
Do not execute the STP or WIT instruction during an A-D conver-
sion.
Instruction Execution Time
The instruction execution time is obtained by multiplying the fre-
quency of the internal clock
φ
by the number of cycles needed to
execute an instruction.
The number of cycles required to execute an instruction is shown
in the list of machine instructions.
The frequency of the internal clock
φ
is half of the X
IN
frequency.
相关PDF资料
PDF描述
M38270E3MXXXFS 16-Bit Buffer/Driver With 3-State Outputs 56-BGA MICROSTAR JUNIOR -40 to 85
M38270E3MXXXGP 16-Bit Buffer/Driver With 3-State Outputs 56-BGA MICROSTAR JUNIOR -40 to 85
M38270E3MXXXHP SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M38270E4MXXXFP SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M38270E4MXXXFS SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
相关代理商/技术参数
参数描述
M3828 BK001 制造商:Alpha Wire Company 功能描述:CBL 3COND 16AWG BLK 1000'
M3828 BK002 制造商:Alpha Wire Company 功能描述:CBL 3COND 16AWG BLK 500'
M3828 BK005 制造商:Alpha Wire Company 功能描述:CBL 3COND 16AWG BLK 100'
M3828 BK199 制造商:Alpha Wire Company 功能描述:CBL 3COND 16AWG BLK 3000=3000'
M3829 BK001 制造商:Alpha Wire Company 功能描述:CBL 4COND 16AWG BLK 1000'