- 您现在的位置：买卖IC网 > PDF目录362867 > M38C37M2MXXXFP (Mitsubishi Electric Corporation) Replaced by TLV320AIC20K : Low-Power Stereo Voice Band CODEC 48-TQFP -40 to 85 PDF资料下载
参数资料
| 型号： | M38C37M2MXXXFP |
| 厂商： | Mitsubishi Electric Corporation |
| 元件分类： | Codec |
| 英文描述： | Replaced by TLV320AIC20K : Low-Power Stereo Voice Band CODEC 48-TQFP -40 to 85 |
| 中文描述： | 单芯片8位CMOS微机 |
| 文件页数： | 40/62页 |
| 文件大小： | 881K |
| 代理商： | M38C37M2MXXXFP |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页当前第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页
40
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
MITSUBISHI MICROCOMPUTERS
38C3 Group
NOTES ON PROGRAMMING
Processor Status Register
The contents of the processor status register (PS) after a reset are
undefined, except for the interrupt disable flag (I) which is “1.” After a
reset, initialize flags which affect program execution. In particular, it
is essential to initialize the index X mode (T) and the decimal mode
(D) flags because of their effect on calculations.
Interrupts
The contents of the interrupt request bits do not change immediately
after they have been written. After writing to an interrupt request reg-
ister, execute at least one instruction before performing a BBC or
BBS instruction.
Decimal Calculations
To calculate in decimal notation, set the decimal mode flag (D) to
“1,” then execute an ADC or SBC instruction. After executing an
ADC or SBC instruction, execute at least one instruction before
executing a SEC, CLC, or CLD instruction.
In decimal mode, the values of the negative (N), overflow (V), and
zero (Z) flags are invalid.
Timers
If a value n (between 0 and 255) is written to a timer latch, the fre-
quency division ratio is 1/(n+1).
Multiplication and Division Instructions
The index X mode (T) and the decimal mode (D) flags do not affect
the MUL and DIV instruction.
The execution of these instructions does not change the contents
of the processor status register.
Ports
The contents of the port direction registers cannot be read. The fol-
lowing cannot be used:
The data transfer instruction (LDA, etc.)
The operation instruction when the index X mode flag (T) is “1”
The addressing mode which uses the value of a direction register
as an index
The bit-test instruction (BBC or BBS, etc.) to a direction register
The read-modify-write instructions (ROR, CLB, or SEB, etc.) to a
direction register.
Use instructions such as LDM and STA, etc., to set the port direction
registers.
Serial I/O
Using an external clock
When using an external clock, input “H” to the external clock input
pin and clear the serial I/O interrupt request bit before executing
serial I/O transfer and serial I/O automatic transfer.
Using an internal clock
When using an internal clock, set the synchronous clock to the in-
ternal clock, then clear the serial I/O interrupt request bit before
executing a serial I/O transfer and serial I/O automatic transfer.
A-D Converter
The comparator uses internal capacitors whose charge will be lost if
the clock frequency is too low.
Therefore, make sure that f(X
IN
) is at least on 500 kHz during an A-D
conversion.
Do not execute the STP or WIT instruction during an A-D conversion.
Instruction Execution Time
The instruction execution time is obtained by multiplying the frequency
of the internal system clock by the number of cycles needed to ex-
ecute an instruction.
The number of cycles required to execute an instruction is shown in
the list of machine instructions.
The frequency of the internal system clock is the same half of the X
IN
frequency in high-speed mode.
At STP Instruction Release
At the STP instruction release, all bits of the timer 12 mode register
are cleared.
NOTES ON USE
Notes on Built-in EPROM Version
The P5
1
pin of the One Time PROM version or the EPROM version
functions as the power source input pin of the internal EPROM.
Therefore, this pin is set at low input impedance, thereby being af-
fected easily by noise.
To prevent a malfunction due to noise, insert a resistor (approx. 5 k
)
in series with the P5
1
pin.
相关PDF资料 |
PDF描述 |
|---|---|
| M38C37M2MXXXFS | Replaced by TLV320AIC20K : Low-Power Stereo Voice Band CODEC 48-TQFP -40 to 85 |
| M38C37M3AXXXFP | Replaced by TLV320AIC20K : Low-Power Stereo Voice Band CODEC 48-TQFP -40 to 85 |
| M38C37M3AXXXFS | Replaced by TLV320AIC20K : Low-Power Stereo Voice Band CODEC 48-TQFP -40 to 85 |
| M38C37M3MXXXFP | Replaced by TLV320AIC22C : Dual VOIP Codec 48-LQFP -40 to 85 |
| M38C37M3MXXXFS | Replaced by TLV320AIC22C : Dual VOIP Codec 48-LQFP -40 to 85 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| M38C59GFHP#U0 | 制造商:Renesas Electronics Corporation 功能描述:MCU 2/4V 60K PB-FREE - Trays |
| M38D20F1XXXFP | 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M38D20F1XXXHP | 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M38D20F2XXXFP | 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M38D20F2XXXHP | 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
发布紧急采购，3分钟左右您将得到回复。