- 您现在的位置：买卖IC网 > PDF目录15905 > MAX17043G+T (Maxim Integrated Products)IC 2-WIRE FG MODEL GAUGE LO BATT PDF资料下载
参数资料
| 型号： | MAX17043G+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 11/14页 |
| 文件大小： | 0K |
| 描述： | IC 2-WIRE FG MODEL GAUGE LO BATT |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 10,000 |
| 系列： | ModelGauge™ |
| 功能： | 燃料，电量检测计/监控器 |
| 电池化学： | 锂离子（Li-Ion） |
| 电源电压： | 2.5 V ~ 4.5 V |
| 工作温度： | -20°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-WFDFN 裸露焊盘 |
| 供应商设备封装： | 8-TDFN-EP（2x3） |
| 包装： | 带卷 (TR) |
| 其它名称： | 90-2771G+BTR |
MAX17043/MAX17044
Compact, Low-Cost 1S/2S Fuel Gauges
with Low-Battery Alert
2-Wire Bus System
The 2-wire bus system supports operation as a slave-
only device in a single or multislave, and single or multi-
master system. Slave devices can share the bus by
uniquely setting the 7-bit slave address. The 2-wire
interface consists of a serial-data line (SDA) and serial-
clock line (SCL). SDA and SCL provide bidirectional
communication between the MAX17043/MAX17044
slave device and a master device at speeds up to
400kHz. The MAX17043/MAX17044s’ SDA pin operates
bidirectionally; that is, when the MAX17043/MAX17044
receive data, SDA operates as an input, and when the
MAX17043/MAX17044 return data, SDA operates as an
open-drain output, with the host system providing a
resistive pullup. The MAX17043/MAX17044 always
operate as a slave device, receiving and transmitting
data under the control of a master device. The master
initiates all transactions on the bus and generates the
SCL signal, as well as the START and STOP bits, which
begin and end each transaction.
Bit Transfer
One data bit is transferred during each SCL clock
cycle, with the cycle defined by SCL transitioning low-
to-high and then high-to-low. The SDA logic level must
remain stable during the high period of the SCL clock
pulse. Any change in SDA when SCL is high is inter-
preted as a START or STOP control signal.
Bus Idle
The bus is defined to be idle, or not busy, when no
master device has control. Both SDA and SCL remain
high when the bus is idle. The STOP condition is the
proper method to return the bus to the idle state.
START and STOP Conditions
The master initiates transactions with a START condi-
tion (S) by forcing a high-to-low transition on SDA while
SCL is high. The master terminates a transaction with a
Acknowledge Bits
Each byte of a data transfer is acknowledged with an
acknowledge bit (A) or a no-acknowledge bit (N). Both
the master and the MAX17043 slave generate acknowl-
edge bits. To generate an acknowledge, the receiving
device must pull SDA low before the rising edge of the
acknowledge-related clock pulse (ninth pulse) and
keep it low until SCL returns low. To generate a no-
acknowledge (also called NAK), the receiver releases
SDA before the rising edge of the acknowledge-related
clock pulse and leaves SDA high until SCL returns low.
Monitoring the acknowledge bits allows for detection of
unsuccessful data transfers. An unsuccessful data
transfer can occur if a receiving device is busy or if a
system fault has occurred. In the event of an unsuc-
cessful data transfer, the bus master should reattempt
communication.
Data Order
A byte of data consists of 8 bits ordered most signifi-
cant bit (MSb) first. The least significant bit (LSb) of
each byte is followed by the acknowledge bit. The
MAX17043/MAX17044 registers composed of multibyte
values are ordered MSb first. The MSb of multibyte reg-
isters is stored on even data-memory addresses.
Slave Address
A bus master initiates communication with a slave
device by issuing a START condition followed by a
slave address (SAddr) and the read/write (R/W) bit.
When the bus is idle, the MAX17043/MAX17044 contin-
uously monitor for a START condition followed by its
slave address. When the MAX17043/MAX17044
receive a slave address that matches the value in the
slave address register, they respond with an acknowl-
edge bit during the clock period following the R/W bit.
The 7-bit slave address is fixed to 6Ch (write)/
6Dh (read):
STOP condition (P), a low-to-high transition on SDA
while SCL is high. A Repeated START condition (Sr)
can be used in place of a STOP then START sequence
MAX17043/MAX17044
SLAVE ADDRESS
0110110
to terminate one transaction and begin another without
returning the bus to the idle state. In multimaster sys-
tems, a Repeated START allows the master to retain
control of the bus. The START and STOP conditions are
the only bus activities in which the SDA transitions
when SCL is high.
Maxim Integrated
Read/Write Bit
The R/W bit following the slave address determines the
data direction of subsequent bytes in the transfer. R/W
= 0 selects a write transaction, with the following bytes
being written by the master to the slave. R/W = 1
selects a read transaction, with the following bytes
being read from the slave by the master. (Table 5).
11
相关PDF资料 |
PDF描述 |
|---|---|
| 73083-BB-24 | CABLE SMA QC PLUG-PLUG RG316 24" |
| VI-J5D-EZ-F1 | CONVERTER MOD DC/DC 85V 25W |
| SRU3028-330Y | INDUCTOR 33UH 470MA SMD |
| VI-J5B-EZ-F1 | CONVERTER MOD DC/DC 95V 25W |
| 5697-240 | CABLE BNC MALE W/O BOOT 240" |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX17043X+ | 功能描述:电池管理 1S/2S Fuel Gauge RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| MAX17043X+T10 | 功能描述:电池管理 1S/2S Fuel Gauge RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| MAX17043X+U | 功能描述:电池管理 RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| MAX17044G+T | 功能描述:电池管理 1S/2S Fuel Gauge RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| MAX17044G+U | 制造商:Maxim Integrated Products 功能描述:2-WIRE FG W/MD GAUGE W/LOW BATT ALE - Rail/Tube |
发布紧急采购，3分钟左右您将得到回复。