- 您现在的位置：买卖IC网 > PDF目录16769 > MAX17710G+T (Maxim Integrated Products)IC ENERGY HARVEST MNGR 12UTDFN PDF资料下载
参数资料
| 型号： | MAX17710G+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 15/18页 |
| 文件大小： | 0K |
| 描述： | IC ENERGY HARVEST MNGR 12UTDFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 1 |
| 应用： | 能量收集 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 12-UFDFN 裸露焊盘 |
| 供应商设备封装： | 12-UTDFN-EP（3x3） |
| 包装： | 标准包装 |
| 其它名称： | MAX17710G+TDKR |
MAX17710
Energy-Harvesting Charger and Protector
Regulator Voltage Selection
The SEL1 pin selects at which voltage REG operates.
Connect SEL1 to BATT for 1.8V operation, three-state for
3.3V operation, or connect to GND for 2.3V operation.
Note that the voltage regulation value is latched when
enabled. To change the regulation voltage point, the reg-
PCKP Pin Capacitor Selection
There are several cases when the system might overload
the cell, potentially causing damage. They are prevented
with the PCKP load switch block and external capacitor:
U During startup, when there is an inrush current due to
the application’s load and capacitance.
U When the cell is cold (such as -40 N C), and due to
increased cell resistance, it is unable to support high-
load currents.
U If the system requires a load current higher than can be
supported by the cell alone.
The device provides cell undervoltage protection by
limiting the current from BATT to PCKP and guarantee-
ing that the cell voltage does not fall below 2.15V. In
Table 3. Regulator Output Voltage Selection
SEL1 PIN CONNECTION
Connect to BATT
Open circuit
Connect to GND
addition to voltage protection, the ramp of the PCKP
switch impedance is changed slowly (5ms to full on) to
gradually load the cell and not collapse the voltage on a
room-temperature cell. Because of these protection fea-
tures, an application can now support brief high-current
pulses by including a large capacitance at PCKP. This
allows support for pulse loads many times higher than
that naturally supported by the cell alone.
A large PCKP capacitance can be selected to support
a pulse load even while the cell is very cold, and would
normally be incapable of supporting a significant load.
Choose this capacitor according to Table 4 or the follow-
ing equation:
C PCKP = I TASK x t TASK /(3.7 - V MIN )
where:
I TASK is the current required to sustain a required task,
t TASK is the time duration of the task, and V MIN is the
minimum voltage of the load doing the task.
This equation assumes that the BATT impedance is high
and cannot support the load.
REG PIN OUTPUT VOLTAGE (V)
1.8
3.3
2.3
Table 4. PCKP Pin Capacitor Values by Application
V MIN
3.0
3.0
2.8
2.8
2.3
2.3
t TASK (ms)
5
5
5
5
5
5
I TASK (mA)
8
4
5
2.5
5
10
C PCKP (μF)*
100
50
28
14
18
36
*Capacitance value tolerances need to be considered.
Maxim Integrated
15
相关PDF资料 |
PDF描述 |
|---|---|
| CRN-1/16-0-SP | HEAT SHRINK TUBING |
| 462A046-3/86-0 | BOOT MOLDED |
| V48C3V3T50B2 | CONVERTER MOD DC/DC 3.3V 50W |
| B78108S1225J9 | CHOKE RF 2200UH 80MA AXIAL |
| RNF-100-3/8-CL-STK | HEAT SHRINK TUBING |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX17711EVKIT+ | 制造商:Maxim Integrated Products 功能描述:AMD SVI1 CPU CONTROLLER 3PHASE - Boxed Product (Development Kits) |
| MAX17711GTM+ | 制造商:Maxim Integrated Products 功能描述:AMD SVI1 CPU CONTROLLER 3PHASE - Rail/Tube |
| MAX1771C/D | 功能描述:DC/DC 开关控制器 12V or Adjustable High-Efficiency Low IQ Step-Up DC-DC Controller RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX1771C/D+ | 功能描述:DC/DC 开关控制器 RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX1771C/W+ | 功能描述:DC/DC 开关控制器 32V or Adjustable High-Efficiency Low-Iq Step-Up DC-DC Controller RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
发布紧急采购，3分钟左右您将得到回复。