- 您现在的位置：买卖IC网 > PDF目录383352 > MAX3042BCWE (MAXIM INTEGRATED PRODUCTS INC) 【10kV ESD-Protected, Quad 5V RS-485/RS-422 Transmitters PDF资料下载
参数资料
| 型号： | MAX3042BCWE |
| 厂商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分类： | 通用总线功能 |
| 英文描述： | 【10kV ESD-Protected, Quad 5V RS-485/RS-422 Transmitters |
| 中文描述： | QUAD LINE DRIVER, PDSO16 |
| 封装： | SO-16 |
| 文件页数： | 9/15页 |
| 文件大小： | 262K |
| 代理商： | MAX3042BCWE |
M
±10kV ESD-Protected, Quad 5V RS-485/RS-422
Transmitters
_______________________________________________________________________________________
9
IEC 1000-4-4 Burst/Electrical Fast
Transient Test Levels
(For Communication Lines)
The stresses are applied while the MAX3040
–
MAX3045
are powered up. Test results are reported as:
1) Normal performance within the specification limits.
2) Temporary degradation or loss of function or perfor-
mance which is self-recoverable.
3) Temporary degradation, loss of function or perfor-
mance requiring operator intervention, such as sys-
tem reset.
4) Degradation or loss of function not recoverable due
to damage.
The MAX3040
–
MAX3045 meets classification 2 listed
above. Additionally, the MAX3040
–
MAX3045 will not
latchup during the IEC burst stress events.
Hot-Swap Capability
Hot-Swap Inputs
When circuit boards are plugged into a
“
hot
”
back-
plane, there can be disturbances to the differential sig-
nal levels that could be detected by receivers
connected to the transmission line. This erroneous data
could cause data errors to an RS-485/RS-422 system.
To avoid this, the MAX3040
–
MAX3045 have hot-swap
capable inputs.
When a circuit board is plugged into a
“
hot
”
backplane
there is an interval during which the processor is going
through its power-up sequence. During this time, the
processor
’
s output drivers are high impedance and will
be unable to drive the enable inputs of the
MAX3040
–
MAX3045 (EN,
EN
, EN_) to defined logic lev-
els. Leakage currents from these high impedance dri-
vers, of as much as 10μA, could cause the enable
inputs of the MAX3040
–
MAX3045 to drift high or low.
Additionally, parasitic capacitance of the circuit board
could cause capacitive coupling of the enable inputs to
either GND or V
CC
. These factors could cause the
enable inputs of the MAX3040
–
MAX3045 to drift to lev-
els that may enable the transmitter outputs (Y_ and Z_).
To avoid this problem, the hot-swap input provides a
method of holding the enable inputs of the
MAX3040
–
MAX3045 in the disabled state as V
CC
ramps up. This hot-swap input is able to overcome the
leakage currents and parasitic capacitances that may
pull the enable inputs to the enabled state.
Hot-Swap Input Circuitry
In the MAX3040
–
MAX3045 the enable inputs feature
hot-swap capability. At the input there are two NMOS
devices, Q1 and Q2 (Figure 9). When V
CC
is ramping
up from 0, an internal 10μs timer turns on Q2 and sets
the SR latch, which also turns on Q1. Transistors Q2, a
700μA current sink, and Q1, an 85μA current sink, pull
EN to GND through a 5.6k
resistor. Q2 is designed to
pull the EN input to the disabled state against an exter-
nal parasitic capacitance of up to 100pF that is trying to
enable the EN input. After 10μs, the timer turns Q2 off
and Q1 remains on, holding the EN input low against
three-state output leakages that might enable EN. Q1
remains on until an external source overcomes the
U = HIGH-VOLTAGE SOURCE
R
C
= CHARGING RESISTOR
C
E
= ENERGY STORAGE CAPACITOR
R
S
= PULSE DURATION SHAPING RESISTOR
R
M
= IMPEDANCE MATCHING RESISTOR
C
D
= DC BLOCKING CAPACITOR
SPARK GAP
U
R
C
R
S
R
M
C
D
C
E
50
COAXIAL
OUTPUT
Figure 7. Simplified Circuit Diagram of a Fast Transient/Burst
Generator
REPETITION PERIOD (DEPENDS ON THE TEST VOLTAGE LEVER,
IN CONFORMITY WITH THE VALUES INDICATED IN 6.1.2).
BURST
BURST DURATION
BURST PERIOD 300ms
PULSE
15ms
Figure 8. General Graph of a Fast Transient Burst
相关PDF资料 |
PDF描述 |
|---|---|
| MAX3040 | Fixed-Point Digital Signal Processor 376-BGA |
| MAX3040CSE | 【10kV ESD-Protected, Quad 5V RS-485/RS-422 Transmitters |
| MAX3040CWE | 【10kV ESD-Protected, Quad 5V RS-485/RS-422 Transmitters |
| MAX3041CSE | 【10kV ESD-Protected, Quad 5V RS-485/RS-422 Transmitters |
| MAX3041CUE | 【10kV ESD-Protected, Quad 5V RS-485/RS-422 Transmitters |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX3042BCWE+ | 功能描述:RS-422/RS-485 接口 IC RoHS:否 制造商:Maxim Integrated 数据速率:1136 Kbps 工作电源电压:3 V to 5.5 V 电源电流:5.9 mA 工作温度范围:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-28 封装:Tube |
| MAX3042BCWE+G126 | 功能描述:RS-422/RS-485 接口 IC +/-10kV ESD-Protected Quad 5V RS-485/422 Transmitters RoHS:否 制造商:Maxim Integrated 数据速率:1136 Kbps 工作电源电压:3 V to 5.5 V 电源电流:5.9 mA 工作温度范围:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-28 封装:Tube |
| MAX3042BCWE+T | 功能描述:RS-422/RS-485 接口 IC RoHS:否 制造商:Maxim Integrated 数据速率:1136 Kbps 工作电源电压:3 V to 5.5 V 电源电流:5.9 mA 工作温度范围:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-28 封装:Tube |
| MAX3042BCWE+TG126 | 功能描述:RS-422/RS-485 接口 IC 10kV ESD-Protected Quad 5V RS-485/RS-422 Transmitters RoHS:否 制造商:Maxim Integrated 数据速率:1136 Kbps 工作电源电压:3 V to 5.5 V 电源电流:5.9 mA 工作温度范围:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-28 封装:Tube |
| MAX3042BCWE-T | 功能描述:RS-422/RS-485 接口 IC RoHS:否 制造商:Maxim Integrated 数据速率:1136 Kbps 工作电源电压:3 V to 5.5 V 电源电流:5.9 mA 工作温度范围:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-28 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。