- 您现在的位置：买卖IC网 > PDF目录181329 > MBM29PL32TM90TN-E1 (SPANSION LLC) 2M X 16 FLASH 3V PROM, 90 ns, PDSO48 PDF资料下载
参数资料
| 型号： | MBM29PL32TM90TN-E1 |
| 厂商： | SPANSION LLC |
| 元件分类： | PROM |
| 英文描述： | 2M X 16 FLASH 3V PROM, 90 ns, PDSO48 |
| 封装： | PLASTIC, TSOP1-48 |
| 文件页数： | 20/72页 |
| 文件大小： | 450K |
| 代理商： | MBM29PL32TM90TN-E1 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页当前第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页
Retired Product
DS05-20907-4E_July 31, 2007
MBM29PL32TM/BM90/10
27
Temporary Sector Group Unprotection
This feature allows temporary unprotection of previously protected sector groups of the devices in order to
change data. The Sector Group Unprotection mode is activated by setting the RESET pin to high voltage (VID).
During this mode, formerly protected sector groups can be programmed or erased by selecting the sector group
addresses. Once the VID is taken away from the RESET pin, all the previously protected sector groups will be
protected again. Refer to “Temporary Sector Group Unprotection Timing Diagram” in
■SWITCHING WAVE-
FORMS and “Temporary Sector Group Unprotection Algorithm” in
■FLOW CHART.
Hardware Reset
The devices may be reset by driving the RESET pin to VIL from VIH. The RESET pin has a pulse requirement
and has to be kept low (VIL) for at least “tRP” in order to properly reset the internal state machine. Any operation
in the process of being executed will be terminated and the internal state machine will be reset to the read mode
“tREADY” after the RESET pin is driven low. Furthermore, once the RESET pin goes high, the devices require an
additional “tRH” before it will allow read access. When the RESET pin is low, the devices will be in the standby
mode for the duration of the pulse and all the data output pins will be tri-stated. If a hardware reset occurs during
a program or erase operation, the data at that particular location will be corrupted.
Write Protect (WP)
The Write Protection function provides a hardware method of protecting certain outermost 8K bytes / 4K words
sectors without using VID. This function is one of two provided by the WP/ACC pin.
If the system asserts VIL on the WP/ACC pin, the device disables program and erase functions in the outermost
8K bytes / 4K words sectors independently of whether this sector was protected or unprotected using the method
described in “Sector Group Protection" above.
If the system asserts VIH on the WP/ACC pin, the device reverts of whether the outermost 8K bytes / 4K words
sectors were last set to be protected to the unprotected status. Sector protection or unprotection for this sector
depends on whether this was last protected or unprotected using the method described in “Sector protection/
unprotection”.
Accelerated Program Operation
The device offers accelerated program operation which enables programming in high speed. If the system asserts
VACC to the WP/ACC pin, the device automatically enters the acceleration mode and the time required for program
operation will reduce to about 85%. This function is primarily intended to allow high speed programing, so caution
is needed as the sector group becomes temporarily unprotected.
The system would use a fast program command sequence when programming during acceleration mode. Set
command to fast mode and reset command from fast mode are not necessary. When the device enters the
acceleration mode, the device is automatically set to fast mode. Therefore, the present sequence could be used
for programming and detection of completion during acceleration mode.
Removing VACC from the WP/ACC pin returns the device to normal operation. Do not remove VACC from the WP/
ACC pin while programming. See “Accelerated Program Timing Diagram” in
■SWITCHING WAVEFORM.
相关PDF资料 |
PDF描述 |
|---|---|
| MBN400GR12A | 400 A, 1200 V, N-CHANNEL IGBT |
| MBNC7-J-P-GN-ST-TH1 | BOARD TERMINATED, FEMALE, BNC CONNECTOR, SOLDER, JACK |
| MBNC7-J-P-HN-ST-TH1 | BOARD TERMINATED, FEMALE, BNC CONNECTOR, SOLDER, JACK |
| MBNC7-J-P-MN-ST-TH1 | BOARD TERMINATED, FEMALE, BNC CONNECTOR, SOLDER, JACK |
| MBNC7-P-C-GN-ST-CA3 | CABLE TERMINATED, MALE, BNC CONNECTOR, CRIMP SOLDER, PLUG |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MBM30000 | 功能描述:BRACKET SIDE MOUNT RoHS:是 类别:工业控制，仪表 >> 配件 系列:* 标准包装:1 系列:Aero-Motive® 130117 附件类型:拖车带 适用于相关产品:标准盒式跟踪系统 其它名称:WM6183 |
| MBM30035001 | 制造商:LG Corporation 功能描述:Card,Technical |
| MBM30035015 | 制造商:LG Corporation 功能描述:Card,Technical |
| MBM300A6 | 制造商:HITACHI 制造商全称:Hitachi Semiconductor 功能描述:IGBT MODULE RANGE WITH SOFT AND FAST (SFD) FREE-WHEELING DIODES |
| MBM300GR12A | 制造商:n/a 功能描述:IGBT Module |
发布紧急采购，3分钟左右您将得到回复。