- 您现在的位置：买卖IC网 > PDF目录16708 > VERSAFIT-3X-1-0-SP (TE Connectivity)HEAT SHRINK TUBING PDF资料下载
参数资料
| 型号： | VERSAFIT-3X-1-0-SP |
| 厂商： | TE Connectivity |
| 文件页数： | 4/7页 |
| 文件大小： | 0K |
| 描述： | HEAT SHRINK TUBING |
| 标准包装： | 250 |
| 系列： | Versafit; 3X |
| 类型： | 套管，弹性 |
| 收缩比率： | 3 至 1 |
| 内径 - 提供： | 1.000"（25.4mm） |
| 内径 - 恢复： | 0.334"（8.5mm） |
| 已恢复的墙壁厚度： | 0.025"（0.64mm） |
| 材质： | 聚烯烃 |
| 特点： | 阻燃 |
| 颜色： | 黑 |
| 其它名称： | 7145794002 |
Page 4
4.3.5
4.3.6
4.4
5.
5.1
5.2
5.3
SPECIFICATION RW-3009 ISSUE 3
Dielectric Withstand, Breakdown, and Strength
The dielectric strength of the tubing shall be measured under oil in accordance with ASTM D 2671. Five
150-mm (6-inch) specimens of tubing shall be recovered over a metal mandrel by conditioning for 3 minutes
in a 200 ± 3°C (392 ± 5°F) oven. The mandrel diameter shall be slightly larger than the fully recovered
inside diameter of the tubing being tested. The metal mandrel shall serve as one electrode and a 25mm (1-
inch) wide strip of lead foil wrapped around the outside of the tubing as the other electrode. The test voltage
shall be applied at a rate of rise of 500 volts per second. Thickness measurements for calculating dielectric
strength shall be made adjacent to the point of breakdown. Specimens for dielectric withstand shall be held
for 60 seconds at 2500 volts.
Corrosive Effect
Three specimens of tubing shall be tested for copper contact corrosion in accordance with ASTM D 2671,
Procedure B. Three specimens shall be conditioned for 7 days in a 158.0 ± 1.0°C (316.4 ± 1.8°F) oven.
After conditioning, the specimens shall be visually examined for evidence of corrosion.
REJECTION AND RETEST
Failure of any samples of tubing to conform to any one of the requirements of this specification shall be
cause for rejection of the lot represented. Tubing which has been rejected may be replaced or reworked to
correct the defect and then resubmitted for acceptance. Before resubmitting, full particulars concerning the
rejection and the action taken to correct the defect shall be furnished to the inspector.
PREPARATION FOR DELIVERY
FORM
The tubing shall be supplied on spools, unless otherwise specified.
PACKAGING
Packaging shall be in accordance with good commercial practice.
MARKING
Each container of tubing shall be permanently and legibly marked with the size, quantity, manufacturer's
identification, specification number, product designation, and lot number.
If this document is printed it becomes uncontrolled. Check for the latest revision.
相关PDF资料 |
PDF描述 |
|---|---|
| RBC22DRYI | CONN EDGECARD 44POS DIP .100 SLD |
| HMM08DSXN | CONN EDGECARD 16POS DIP .156 SLD |
| V48C28T75BF3 | CONVERTER MOD DC/DC 28V 75W |
| MT2000-3.0-6-SP | HEAT SHRINK TUBING |
| A3AAH-1436G | IDC CABLE - ASC14H/AE14G/ASC14H |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MC10EL31DTR2G | 功能描述:触发器 5V ECL D-Type w/Set and Reset RoHS:否 制造商:Texas Instruments 电路数量:2 逻辑系列:SN74 逻辑类型:D-Type Flip-Flop 极性:Inverting, Non-Inverting 输入类型:CMOS 输出类型: 传播延迟时间:4.4 ns 高电平输出电流:- 16 mA 低电平输出电流:16 mA 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:X2SON-8 封装:Reel |
| MC10EL32D | 功能描述:时钟驱动器及分配 5V ECL Divide By 2 RoHS:否 制造商:Micrel 乘法/除法因子:1:4 输出类型:Differential 最大输出频率:4.2 GHz 电源电压-最大: 电源电压-最小:5 V 最大工作温度:+ 85 C 封装 / 箱体:SOIC-8 封装:Reel |
| MC10EL32DG | 功能描述:时钟驱动器及分配 5V ECL Divide By 2 Divider RoHS:否 制造商:Micrel 乘法/除法因子:1:4 输出类型:Differential 最大输出频率:4.2 GHz 电源电压-最大: 电源电压-最小:5 V 最大工作温度:+ 85 C 封装 / 箱体:SOIC-8 封装:Reel |
| MC10EL32DR2 | 功能描述:时钟驱动器及分配 5V ECL Divide By 2 RoHS:否 制造商:Micrel 乘法/除法因子:1:4 输出类型:Differential 最大输出频率:4.2 GHz 电源电压-最大: 电源电压-最小:5 V 最大工作温度:+ 85 C 封装 / 箱体:SOIC-8 封装:Reel |
| MC10EL32DR2G | 功能描述:时钟驱动器及分配 5V ECL Divide By 2 Divider RoHS:否 制造商:Micrel 乘法/除法因子:1:4 输出类型:Differential 最大输出频率:4.2 GHz 电源电压-最大: 电源电压-最小:5 V 最大工作温度:+ 85 C 封装 / 箱体:SOIC-8 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。