- 您现在的位置：买卖IC网 > PDF目录3281 > ICL7650CSD (Maxim Integrated Products)IC OPAMP CHOPPER/STABLE 14-SOIC PDF资料下载
参数资料
| 型号： | ICL7650CSD |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 12/12页 |
| 文件大小： | 0K |
| 描述： | IC OPAMP CHOPPER/STABLE 14-SOIC |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 50 |
| 放大器类型： | 断路器（零漂移） |
| 电路数： | 1 |
| 转换速率： | 2.5 V/µs |
| 增益带宽积： | 2MHz |
| 电流 - 输入偏压： | 1.5pA |
| 电压 - 输入偏移： | 700µV |
| 电流 - 电源： | 1.2mA |
| 电压 - 电源，单路/双路(±)： | 4.5 V ~ 16 V，±2.25 V ~ 8 V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 14-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 14-SOIC |
| 包装： | 管件 |
The 14-pin DIP configuration has been specifically
designed to ease input guarding. The pins adjacent to
the inputs are not used.
Pin Compatibility
The ICL7653’s pinout generally corresponds to that of
industry-standard 8-pin devices such as the LM741 or
LM101. However, its external null storage capacitors
are connected to pins 1 and 8; whereas most op amps
leave these pins open or use them for offset null or
compensation capacitors.
The OP05 and OP07 op amps can be converted for
ICL7650/ICL7653 operation. This can be accomplished
by removing the offset null potentiometer, which is con-
nected from pins 1 and 8 to V+, and replacing it with
two capacitors connected from pins 1 and 8 to V-. For
LM108 devices, the compensation capacitor is
replaced by the external nulling capacitors. Pin 5 is the
output clamp connection on the ICL7650/ICL7653. By
removing any circuit connections from this pin, the
LM101/LM748/LM709 devices can undergo a similar
conversion.
Typical Applications
Figure 4 shows the ICL7650/ICL7653 automatically
nulling the offset voltage of a high-speed amplifier. The
ICL7650/ICL7653 continuously monitor the voltage at
the amplifier’s inverting input, integrate the error, and
drive the amplifier’s noninverting input to correct for the
offset voltage detected at the inverting input. The cir-
cuit’s DC offset characteristics are determined by the
ICL7650/ICL7653, and its AC performance is deter-
mined by the high-speed amplifier. While this circuit
continuously and automatically adjusts the amplifier’s
offset to less than 5V, it does not correct for errors
caused by the input bias current, so the value of resis-
tor RF should be as low as is practical. This technique
can be used with any op amp that is configured as an
inverting amplifier.
Figures 5 and 6 illustrate basic inverting and noninvert-
ing amplifier circuits. Both figures show an output
clamping circuit being used to enhance overload
recovery performance. Supply voltage (±8V max) and
output drive capability (10k
load for full swing) are the
only limitations to consider when replacing other op
amps with the ICL7650/ICL7653. Use a simple booster
circuit to overcome these limitations (Figure 7). This
enables the full output capabilities of the LM118 (or any
other standard device) to be combined with the input
capabilities of the ICL7650/ICL7653. Observe the loop
gain stability carefully when the feedback network is
added, particularly when a slower amplifier such as the
LM741 is used.
A lower voltage supply is required when mixing the
ICL7650/ICL7653 with circuits that operate at ±15V sup-
plies. One approach is to use a highly efficient voltage
divider. This is illustrated in Figure 8, where the ICL7660
voltage converter is used to convert +15V to +7.5V.
ICL7650/ICL7650B/ICL7653/ICL7653B
Chopper-Stabilized Op Amps
_______________________________________________________________________________________
9
HIGH-
SPEED
AMP
0.1
F
47
10k
100k
RF
ICL7650
ICL7653
VOUT
RIN
ICL7650
OUTPUT
(R1 || R2)
≥ 100k
FOR FULL CLAMP EFFECT
INPUT
C
R
C
CLAMP
0.1
F 0.1F
R2
R1
1k
NOTE: R1 || R2 INDICATES THE
PARALLEL COMBINATION OF
R1 || R2.
Figure 4. Nulling a High-Speed Amplifier
Figure 5. Inverting Amplifier with Optional Clamp
相关PDF资料 |
PDF描述 |
|---|---|
| ICL7616ACSA | IC OPAMP LP CMOS 8-SOIC |
| RMCF2010JT24R0 | RES 24 OHM 5% 3/4W 2010 SMD |
| MAX472CPA | IC AMP CURR-SENSE HI-SIDE 8-DIP |
| MAX479CPD | IC OPAMP SNGL SUP QUAD 14-DIP |
| RMCF2010JT820R | RES 820 OHM 3/4W 5% 2010 SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| NCV2002SN2T1G | 功能描述:运算放大器 - 运放 0.9-7V Sngl Rail to Rail Extended Temp RoHS:否 制造商:STMicroelectronics 通道数量:4 共模抑制比（最小值）:63 dB 输入补偿电压:1 mV 输入偏流（最大值）:10 pA 工作电源电压:2.7 V to 5.5 V 安装风格:SMD/SMT 封装 / 箱体:QFN-16 转换速度:0.89 V/us 关闭:No 输出电流:55 mA 最大工作温度:+ 125 C 封装:Reel |
| NCV2200SN1T1G | 功能描述:IC COMPARATOR COMPL SOT-23-5 RoHS:是 类别:集成电路 (IC) >> 线性 - 比较器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 类型:通用 元件数:1 输出类型:CMOS，推挽式，满摆幅，TTL 电压 - 电源，单路/双路(±):2.5 V ~ 5.5 V，±1.25 V ~ 2.75 V 电压 - 输入偏移（最小值）:5mV @ 5.5V 电流 - 输入偏压（最小值）:1pA @ 5.5V 电流 - 输出（标准）:- 电流 - 静态（最大值）:24µA CMRR, PSRR（标准）:80dB CMRR，80dB PSRR 传输延迟（最大）:450ns 磁滞:±3mV 工作温度:-40°C ~ 85°C 封装/外壳:6-WFBGA，CSPBGA 安装类型:表面贴装 包装:管件 其它名称:Q3554586 |
| NCV2200SN2T1G | 功能描述:校验器 IC ANA COMPARATORS RoHS:否 制造商:STMicroelectronics 产品: 比较器类型: 通道数量: 输出类型:Push-Pull 电源电压-最大:5.5 V 电源电压-最小:1.1 V 补偿电压（最大值）:6 mV 电源电流（最大值）:1350 nA 响应时间: 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:SC-70-5 封装:Reel |
| NCV2574 | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:0.5 A, Adjustable Output Voltage, Step−Down Switching Regulator |
| NCV2574DW-ADJR2 | 功能描述:直流/直流开关调节器 ASECLSW REG RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
发布紧急采购，3分钟左右您将得到回复。