- 您现在的位置：买卖IC网 > PDF目录268194 > NE57607GDH-T (NXP SEMICONDUCTORS) 2-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8 PDF资料下载
参数资料
| 型号： | NE57607GDH-T |
| 厂商： | NXP SEMICONDUCTORS |
| 元件分类： | 电源管理 |
| 英文描述： | 2-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8 |
| 封装： | 4.40 MM, PLASTIC, SOT-530-1, VSOP-8 |
| 文件页数： | 7/10页 |
| 文件大小： | 131K |
| 代理商： | NE57607GDH-T |
Philips Semiconductors
Product data
NE57607
Two-cell Lithium-ion battery protection with
overcurrent, over- and under-voltage protection
2001 Oct 03
6
Charging Lithium cells
The lithium cells must be charged with a dedicated charging IC such
as the NE57600. These dedicated charging ICs perform a
current-limited, constant-voltage charge, as shown in Figure 4.
The charger IC begins charging with a current that is typically the
rating of the cell (1C) or the milliampere rating of the cell. As the cell
approaches its full-charge voltage rating (VOV), the current entering
the cell decreases, and the charger IC provides a constant voltage.
When the charge current falls below a preset amount, 50 mA for
example, the charge is discontinued.
If charging is begun below the overdischarged voltage rating of the
cell, it is important to slowly raise the cell voltage up to this
overdischarged voltage level. This is done by a reconditioning
charge. A small amount of current is provided to the cell (50 mA for
example), and the cell voltage is allowed a period of time to rise to
the overdischarged voltage. If the cell voltage recovers, then a
normal charging sequence can begin. If the cell does not reach the
overdischarged voltage level, then the cell is too damaged to charge
and the charge is discontinued.
To take advantage of the larger energy density of lithium cells it is
important to allow enough time to completely charge the cell. When
the charger switches from constant current to constant voltage
charge (Point B, Figure 4) the cell only contains about 80 percent of
its full capacity. When the cell is 100 mV less than its full rated
charge voltage the capacity contained within the cell is 95 percent.
Hence, allowing the cell to slowly complete its charge takes
advantage of the larger capacity of the lithium cells.
SL01554
CHARGE
CURRENT
(%C)
1.0
0.5
1.0
2.0
OPEN-CIRCUIT
CELL
VOL
T
AGE
(V)
3.0
4.0
1.0
2.0
Point B
Vov
TIME (HOURS)
CONSTANT
VOLTAGE
CONSTANT
CURRENT
Figure 4. Lithium cell charging curves.
FUNCTIONAL DIAGRAM
NE57607
2
4
1
5
8
3
CS
CF
DF
OC Ref
OV Ref
UV Ref
6
OV Ref
UV Ref
7
SL01566
VC1
VC2
OV DEADTIME
CONTROL
UV DEADTIME
CONTROL
VCC
GND
CDLY
CHARGER
DETECTOR
Figure 5. Functional diagram.
相关PDF资料 |
PDF描述 |
|---|---|
| NJU7707F26A1 | POWER SUPPLY SUPPORT CKT, PDSO5 |
| NSR368-79I | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| NSR368-79LIPC | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| NFC40-24S12-M4E | 1-OUTPUT 40 W DC-DC REG PWR SUPPLY MODULE |
| NFC40-24S05-MX | 1-OUTPUT 40 W DC-DC REG PWR SUPPLY MODULE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| NE57607H | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:Two-cell Lithium-ion battery protection with overcurrent, over- and under-voltage protection |
| NE57607HDH | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:Two-cell Lithium-ion battery protection with overcurrent, over- and under-voltage protection |
| NE57607K | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:Two-cell Lithium-ion battery protection with overcurrent, over- and under-voltage protection |
| NE57607KDH | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:Two-cell Lithium-ion battery protection with overcurrent, over- and under-voltage protection |
| NE57607XDH | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:Two-cell Lithium-ion battery protection with overcurrent, over- and under-voltage protection |
发布紧急采购，3分钟左右您将得到回复。