参数资料
型号: PCA9685BS,118
厂商: NXP Semiconductors
文件页数: 27/51页
文件大小: 0K
描述: IC LED DVR PWM 16CH HVQFN28
产品培训模块: I²C Bus Fundamentals
标准包装: 1
拓扑: 开路漏极,PWM
输出数: 16
内部驱动器:
类型 - 主要: 背光,LED 闪烁器
类型 - 次要: RGBA
频率: 25MHz,50MHz
电源电压: 2.3 V ~ 5.5 V
输出电压: 5.5V
安装类型: 表面贴装
封装/外壳: 28-VQFN 裸露焊盘
供应商设备封装: 28-HVQFN(6x6)
包装: 标准包装
工作温度: -40°C ~ 85°C
其它名称: 568-5305-6
NXP Semiconductors
PCA9685
16-channel, 12-bit PWM Fm+ I 2 C-bus LED controller
7.6 Software reset
The Software Reset Call (SWRST Call) allows all the devices in the I 2 C-bus to be reset to
the power-up state value through a specific formatted I 2 C-bus command. To be performed
correctly, it implies that the I 2 C-bus is functional and that there is no device hanging the
bus.
The SWRST Call function is defined as the following:
1. A START command is sent by the I 2 C-bus master.
2. The reserved SWRST I 2 C-bus address ‘0000 000’ with the R/W bit set to ‘0’ (write) is
sent by the I 2 C-bus master.
3. The PCA9685 device(s) acknowledge(s) after seeing the General Call address
‘0000 0000’ (00h) only. If the R/W bit is set to ‘1’ (read), no acknowledge is returned to
the I 2 C-bus master.
4. Once the General Call address has been sent and acknowledged, the master sends
1 byte with 1 specific value (SWRST data byte 1):
a. Byte 1 = 06h: the PCA9685 acknowledges this value only. If byte 1 is not equal to
06h, the PCA9685 does not acknowledge it.
If more than 1 byte of data is sent, the PCA9685 does not acknowledge any more.
5. Once the correct byte (SWRST data byte 1) has been sent and correctly
acknowledged, the master sends a STOP command to end the SWRST Call: the
PCA9685 then resets to the default value (power-up value) and is ready to be
addressed again within the specified bus free time (t BUF ).
General Call address
SWRST data byte 1
S
0
0
0
0
0
0
0
0
A
0
0
0
0
0
1
1
0
A
P
START condition
acknowledge
from slave
acknowledge
from slave
STOP
condition
002aac900
Fig 12. SWRST Call
The I 2 C-bus master must interpret a non-acknowledge from the PCA9685 (at any time) as
a ‘SWRST Call Abort’. The PCA9685 does not initiate a reset of its registers. This
happens only when the format of the SWRST Call sequence is not correct.
PCA9685
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 3 — 2 September 2010
? NXP B.V. 2010. All rights reserved.
27 of 51
相关PDF资料
PDF描述
VI-BWD-CV-F4 CONVERTER MOD DC/DC 85V 150W
ESC60DREF-S734 CONN EDGECARD 120POS .100 EYELET
TAP686K010FCS CAP TANT 68UF 10V 10% RADIAL
VI-BWJ-CV-F1 CONVERTER MOD DC/DC 36V 150W
ABM02DRTN CONN EDGECARD 4POS DIP .156 SLD
相关代理商/技术参数
参数描述
PCA9685PW 制造商:NXP Semiconductors 功能描述:IC LED DRIVER RGBA 28-TSSOP 制造商:NXP Semiconductors 功能描述:IC, LED DRIVER, RGBA, 28-TSSOP 制造商:NXP Semiconductors 功能描述:IC, LED DRIVER, RGBA, 28-TSSOP; No. of Outputs:16; Output Current:25mA; Output Voltage:5.5V; Driver Case Style:TSSOP; Input Voltage Min:2.3V; Input Voltage Max:5.5V; Dimming Control Type:PWM; Switching Frequency:1MHz; Operating ;RoHS Compliant: Yes
PCA9685PW,112 功能描述:LED显示驱动器 I2C Bus LED Controller 28-Pin RoHS:否 制造商:Micrel 数位数量:5 片段数量: 安装风格:SMD/SMT 封装 / 箱体:PLCC-44 工作电源电压:4.75 V to 11 V 最大电源电流:10 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装:Tube
PCA9685PW,118 功能描述:LED显示驱动器 I2C Bus LED Controller 28-Pin RoHS:否 制造商:Micrel 数位数量:5 片段数量: 安装风格:SMD/SMT 封装 / 箱体:PLCC-44 工作电源电压:4.75 V to 11 V 最大电源电流:10 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装:Tube
PCA9685PW/Q900,118 功能描述:LED显示驱动器 LED Driver 2.3V-5.5V 6mA RoHS:否 制造商:Micrel 数位数量:5 片段数量: 安装风格:SMD/SMT 封装 / 箱体:PLCC-44 工作电源电压:4.75 V to 11 V 最大电源电流:10 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装:Tube
PCA9691BS/1 制造商:NXP Semiconductors 功能描述:IC ADC/DAC 8-BIT I2C 16-HVQFN 制造商:NXP Semiconductors 功能描述:IC, ADC/DAC, 8-BIT, I2C, 16-HVQFN