- 您现在的位置：买卖IC网 > PDF目录4230 > SST39VF3201B-70-4I-EKE-T (Microchip Technology)IC FLASH MPF 32MBIT 70NS 48TSOP PDF资料下载
参数资料
| 型号： | SST39VF3201B-70-4I-EKE-T |
| 厂商： | Microchip Technology |
| 文件页数： | 2/29页 |
| 文件大小： | 0K |
| 描述： | IC FLASH MPF 32MBIT 70NS 48TSOP |
| 标准包装： | 1,000 |
| 系列： | SST39 MPF™ |
| 格式 - 存储器： | 闪存 |
| 存储器类型： | FLASH |
| 存储容量： | 32M（2M x 16） |
| 速度： | 70ns |
| 接口： | 并联 |
| 电源电压： | 2.7 V ~ 3.6 V |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 48-TFSOP（0.724"，18.40mm 宽） |
| 供应商设备封装： | 48-TSOP |
| 包装： | 带卷 (TR) |
第1页当前第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页
32 Mbit Multi-Purpose Flash Plus
SST39VF3201B / SST39VF3202B
Data Sheet
Device Operation
Commands are used to initiate the memory operation func-
tions of the device. Commands are written to the device
using standard microprocessor write sequences. A com-
mand is written by asserting WE# low while keeping CE#
low. The address bus is latched on the falling edge of WE#
or CE#, whichever occurs last. The data bus is latched on
the rising edge of WE# or CE#, whichever occurs first.
The SST39VF320xB also have the Auto Low Power
mode which puts the device in a near standby mode after
data has been accessed with a valid Read operation. This
reduces the I DD active read current from typically 9 mA to
typically 4 μA. The Auto Low Power mode reduces the typi-
cal I DD active read current to the range of 2 mA/MHz of
Read cycle time. The device exits the Auto Low Power
mode with any address transition or control signal transition
used to initiate another Read cycle, with no access time
penalty. Note that the device does not enter Auto-Low
Power mode after power-up with CE# held steadily low,
until the first address transition or CE# is driven high.
Read
The Read operation of the SST39VF320xB is controlled
by CE# and OE#, both have to be low for the system to
obtain data from the outputs. CE# is used for device
selection. When CE# is high, the chip is deselected and
only standby power is consumed. OE# is the output con-
trol and is used to gate data from the output pins. The
data bus is in high impedance state when either CE# or
OE# is high. Refer to the Read cycle timing diagram for
further details (Figure 5).
Word-Program Operation
The SST39VF320xB are programmed on a word-by-word
basis. Before programming, the sector where the word
exists must be fully erased. The Program operation is
accomplished in three steps. The first step is the three-byte
load sequence for Software Data Protection. The second
step is to load word address and word data. During the
Word-Program operation, the addresses are latched on the
falling edge of either CE# or WE#, whichever occurs last.
The data is latched on the rising edge of either CE# or
WE#, whichever occurs first. The third step is the internal
Program operation which is initiated after the rising edge of
the fourth WE# or CE#, whichever occurs first. The Pro-
gram operation, once initiated, will be completed within 10
μs. See Figure 6 and Figure 7 for WE# and CE# controlled
Program operation timing diagrams and Figure 21 for flow-
charts. During the Program operation, the only valid reads
are Data# Polling and Toggle Bit. During the internal Pro-
gram operation, the host is free to perform additional tasks.
Any commands issued during the internal Program opera-
tion are ignored. During the command sequence, WP#
should be statically held high or low.
Sector/Block-Erase Operation
The Sector- (or Block-) Erase operation allows the system
to erase the device on a sector-by-sector (or block-by-
block) basis. The SST39VF320xB offer both Sector-Erase
and Block-Erase mode. The sector architecture is based
on uniform sector size of 2 KWord. The Block-Erase mode
is based on uniform block size of 32 KWord. The Sector-
Erase operation is initiated by executing a six-byte com-
mand sequence with Sector-Erase command (50H) and
sector address (SA) in the last bus cycle. The Block-Erase
operation is initiated by executing a six-byte command
sequence with Block-Erase command (30H) and block
address (BA) in the last bus cycle. The sector or block
address is latched on the falling edge of the sixth WE#
pulse, while the command (50H or 30H) is latched on the
rising edge of the sixth WE# pulse. The internal Erase
operation begins after the sixth WE# pulse. The End-of-
Erase operation can be determined using either Data#
Polling or Toggle Bit methods. See Figure 11 and Figure 12
for timing waveforms and Figure 25 for the flowchart. Any
commands issued during the Sector- or Block-Erase oper-
ation are ignored. When WP# is low, any attempt to Sector-
(Block-) Erase the protected block will be ignored. During
the command sequence, WP# should be statically held
high or low.
Erase-Suspend/Erase-Resume Commands
The Erase-Suspend operation temporarily suspends a
Sector- or Block-Erase operation thus allowing data to be
read from any memory location, or program data into any
sector/block that is not suspended for an Erase operation.
The operation is executed by issuing one byte command
sequence with Erase-Suspend command (B0H). The
device automatically enters read mode typically within 10
μs after the Erase-Suspend command had been issued.
Valid data can be read from any sector or block that is not
suspended from an Erase operation. Reading at address
location within erase-suspended sectors/blocks will output
DQ 2 toggling and DQ 6 at ‘1’. While in Erase-Suspend
mode, a Word-Program operation is allowed except for the
sector or block selected for Erase-Suspend.
To resume Sector-Erase or Block-Erase operation which has
been suspended the system must issue Erase Resume
command. The operation is executed by issuing one byte
command sequence with Erase Resume command (30H)
at any address in the last Byte sequence.
?2009 Silicon Storage Technology, Inc.
2
S71384-01-000
1/09
相关PDF资料 |
PDF描述 |
|---|---|
| XC5VLX30-1FF676I | IC FPGA VIRTEX-5 30K 676FBGA |
| ABB55DHAT | CONN EDGECARD 110PS R/A .050 SLD |
| SST39VF1602-70-4C-B3KE-T | IC FLASH MPF 16MB 70NS 48TFBGA |
| XC2V1000-4FG256I | IC FPGA VIRTEX-II 256FGBGA |
| XC4VLX25-10SFG363I | IC FPGA VIRTEX-4 LX 25K 363FCBGA |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SST39VF3201C-70-4I-B3KE | 功能描述:闪存 2.7V to 3.6V 32Mbit Multi-Prps Fl RoHS:否 制造商:ON Semiconductor 数据总线宽度:1 bit 存储类型:Flash 存储容量:2 MB 结构:256 K x 8 定时类型: 接口类型:SPI 访问时间: 电源电压-最大:3.6 V 电源电压-最小:2.3 V 最大工作电流:15 mA 工作温度:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体: 封装:Reel |
| SST39VF3201C-70-4I-B3KE-T | 功能描述:闪存 2.7V to 3.6V 32Mbit Multi-Prps Fl RoHS:否 制造商:ON Semiconductor 数据总线宽度:1 bit 存储类型:Flash 存储容量:2 MB 结构:256 K x 8 定时类型: 接口类型:SPI 访问时间: 电源电压-最大:3.6 V 电源电压-最小:2.3 V 最大工作电流:15 mA 工作温度:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体: 封装:Reel |
| SST39VF3201C-70-4I-EKE | 功能描述:闪存 2.7V to 3.6V 32Mbit Multi-Prps Fl RoHS:否 制造商:ON Semiconductor 数据总线宽度:1 bit 存储类型:Flash 存储容量:2 MB 结构:256 K x 8 定时类型: 接口类型:SPI 访问时间: 电源电压-最大:3.6 V 电源电压-最小:2.3 V 最大工作电流:15 mA 工作温度:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体: 封装:Reel |
| SST39VF3201C-70-4I-EKE-T | 功能描述:闪存 2.7V to 3.6V 32Mbit Multi-Prps Fl RoHS:否 制造商:ON Semiconductor 数据总线宽度:1 bit 存储类型:Flash 存储容量:2 MB 结构:256 K x 8 定时类型: 接口类型:SPI 访问时间: 电源电压-最大:3.6 V 电源电压-最小:2.3 V 最大工作电流:15 mA 工作温度:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体: 封装:Reel |
| SST39VF3202-70-4C-B3K | 功能描述:闪存 2M X 16 70ns RoHS:否 制造商:ON Semiconductor 数据总线宽度:1 bit 存储类型:Flash 存储容量:2 MB 结构:256 K x 8 定时类型: 接口类型:SPI 访问时间: 电源电压-最大:3.6 V 电源电压-最小:2.3 V 最大工作电流:15 mA 工作温度:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体: 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。