参数资料
| 型号： | X9110TV14IZ-2.7T1 |
| 厂商： | Intersil |
| 文件页数： | 13/18页 |
| 文件大小： | 0K |
| 描述： | IC XDCP 1024-TAP 100K 14-TSSOP |
| 标准包装： | 2,500 |
| 系列： | XDCP™ |
| 接片： | 1024 |
| 电阻（欧姆）： | 100k |
| 电路数： | 1 |
| 温度系数： | 标准值 ±300 ppm/°C |
| 存储器类型： | 非易失 |
| 接口： | 4 线 SPI（芯片选择，设备位址） |
| 电源电压： | 2.7 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 14-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 14-TSSOP |
| 包装： | 带卷 (TR) |
4
FN8158.3
February 13, 2008
Potentiometer Pins
RH, RL
The RH and RL pins are equivalent to the terminal
connections on a mechanical potentiometer.
RW
The wiper pin are equivalent to the wiper terminal of a
mechanical potentiometer.
Bias Supply Pins
SYSTEM SUPPLY VOLTAGE (VCC) AND SUPPLY
GROUND (VSS)
The VCC pin is the system supply voltage. The VSS pin is
the system ground.
ANALOG SUPPLY VOLTAGES (V+ AND V
-)
These supplies are the analog voltage supplies for the
potentiometer. The V+ supply is tied to the wiper switches
while the V- supply is used to bias the switches and the
internal P+ substrate of the integrated circuit. Both of these
supplies set the voltage limits of the potentiometer.
Principles Of Operation
Device Description
SERIAL INTERFACE
The X9110 supports the SPI interface hardware conventions.
The device is accessed via the SI input with data clocked-in
on the rising SCK. CS must be LOW and the HOLD and WP
pins must be HIGH during the entire operation.
The SO and SI pins can be connected together, since they
have three state outputs. This can help to reduce system pin
count.
ARRAY DESCRIPTION
The X9110 is comprised of a resistor array (Figure 1). The
array contains the equivalent of 1023 discrete resistive
segments that are connected in series. The physical ends of
each array are equivalent to the fixed terminals of a
mechanical potentiometer (RH and RL inputs).
At both ends of each array and between each resistor
segment is a CMOS switch connected to the wiper (RW)
output. Within the individual array only one switch may be
turned on at a time.
These switches are controlled by a Wiper Counter Register
(WCR). The 10-bits of the WCR (WCR[9:0]) are decoded to
select, and enable, one of 1024 switches.
WIPER COUNTER REGISTER (WCR)
The X9110 contains a Wiper Counter Register (see Table 1)
for the XDCP potentiometer. The WCR is equivalent to a
serial-in, parallel-out register/counter with its outputs
decoded to select one of 1024 switches along its resistor
array. The contents of the WCR can be altered in one of
three ways: (1) it may be written directly by the host via the
write Wiper Counter Register instruction (serial load); (2) it
SERIAL DATA PATH
FROM INTERFACE
REGISTER 0
SERIAL
BUS
INPUT
PARALLEL
BUS
INPUT
COUNTER
REGISTER
R H
R L
R
W
10
C
O
U
N
T
E
R
D
E
C
O
D
E
If WCR = 000[HEX] then RW = RL
If WCR = 3FF[HEX] then RW = RH
WIPER
(WCR)
(DR0)
CIRCUITRY
REGISTER 1
(DR1)
REGISTER 2
(DR2)
REGISTER 3
(DR3)
FIGURE 1. DETAILED POTENTIOMETER BLOCK DIAGRAM
X9110
相关PDF资料 |
PDF描述 |
|---|---|
| VE-BTZ-MV-B1 | CONVERTER MOD DC/DC 2V 60W |
| X9111TV14IZ-2.7T1 | IC POT DGTL 100K OHM 14-TSSOP |
| VE-BTW-MW-B1 | CONVERTER MOD DC/DC 5.5V 100W |
| VE-2VR-MX-B1 | CONVERTER MOD DC/DC 7.5V 75W |
| VE-BTV-MW-B1 | CONVERTER MOD DC/DC 5.8V 100W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| X9110TV14Z | 功能描述:IC XDCP SGL 1024TAP 100K 14TSSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数字电位器 系列:XDCP™ 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 接片:256 电阻（欧姆）:100k 电路数:2 温度系数:标准值 35 ppm/°C 存储器类型:易失 接口:6 线串行（芯片选择，递增，增/减） 电源电压:2.6 V ~ 5.5 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:14-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:14-TSSOP 包装:带卷 (TR) |
| X9110TV14Z-2.7 | 功能描述:IC XDCP SGL 1024TAP 100K 14TSSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数字电位器 系列:XDCP™ 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 接片:256 电阻（欧姆）:100k 电路数:2 温度系数:标准值 35 ppm/°C 存储器类型:易失 接口:6 线串行（芯片选择，递增，增/减） 电源电压:2.6 V ~ 5.5 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:14-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:14-TSSOP 包装:带卷 (TR) |
| X9110TV14ZT1 | 功能描述:IC XDCP 1024-TAP 100K 14-TSSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数字电位器 系列:XDCP™ 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 接片:256 电阻（欧姆）:100k 电路数:2 温度系数:标准值 35 ppm/°C 存储器类型:易失 接口:6 线串行（芯片选择，递增，增/减） 电源电压:2.6 V ~ 5.5 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:14-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:14-TSSOP 包装:带卷 (TR) |
| X9111 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Single Supply/Low Power/1024-Tap/SPI Bus |
| X9111_06 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Single Digitally-Controlled (XDCP⑩) Potentiometer |
发布紧急采购，3分钟左右您将得到回复。