- 您现在的位置：买卖IC网 > Datasheet目录542 > 0011030036 (Molex Inc)TOOL HAND EXTRACTION Datasheet资料下载
参数资料
| 型号： | 0011030036 |
| 厂商： | Molex Inc |
| 文件页数： | 7/24页 |
| 文件大小： | 0K |
| 描述： | TOOL HAND EXTRACTION |
| 标准包装： | 1 |
| 系列： | SL™ |
| 工具类型： | 拔出工具 |
| 适用于相关产品： | 矩形连接器触点 |
| 产品目录页面： | 193 (CN2011-ZH PDF) |
| 配用： | WM2567CT-ND - CONN PIN 22-24AWG CRIMP 30GOLD WM2565CT-ND - CONN PIN 24-30AWG CRIMP TIN WM2564CT-ND - CONN SOCKET 22-24AWG CRIMP GOLD WM2563CT-ND - CONN PIN 24-30AWG CRIMP 15GOLD WM2562CT-ND - CONN SOCKET 24-30AWG CRIMP TIN WM2567TR-ND - CONN PIN 22-24AWG CRIMP 30GOLD WM2566-ND - CONN PIN 24-30AWG CRIMP 30GOLD WM2565TR-ND - CONN PIN 24-30AWG CRIMP TIN WM2564TR-ND - CONN SOCKET 22-24AWG CRIMP GOLD WM2563TR-ND - CONN PIN 24-30AWG CRIMP 15GOLD 更多... |
| 其它名称： | 0011-03-0036 0011-03-0036-E 0011030036-E 11-03-0036 11-03-0036-E 11030036 11030036-E WM1032 |
Quality Crimp Handbook
To evaluate the insulation crimp section, cut the wire
Cut-off Tab Length
This material protrudes outside the insulation crimp
after the terminal is separated from the carrier strip.
As a rule, the cut-off tab is approximately 1.0 to 1.5
times terminal material thickness. * A cut-off tab
that is too long may expose a terminal outside the
housing or it may fail electrical spacing
requirements. In most situations, a tool is set - up to
provide a cut-off tab that is flush to one material
thickness.
Extrusions (Flash)
These small flares form on the bottom of the
conductor crimp resulting from the clearance
between the punch and anvil tooling. If the anvil is
worn or the terminal is over-crimped, excessive
extrusion is the results. An uneven extrusion may
also result if the punch and anvil alignment is not
correct, if the feed adjustment is off, or if there is
insufficient/excessive terminal drag.
Insulation Crimp (Strain Relief)
This is the part of the terminal that provides wire
support for insertion into the housing. It also allows
the terminal to withstand shock and vibration. The
terminal needs to hold the wire as firmly as possible
without cutting through to the conductor strands.
The acceptability of an insulation crimp is subjective
and depends on the application. A bend test is
recommended to determine whether the strain relief
is acceptable for each particular application.
flush with the back of the terminal. Once the optimum
setting for the application is determined, it is important to
document the insulation crimp height. Then, as part of
the setup procedure, the operator can check the crimp
height.
Insulation Position
This is the location of the insulation in relation to the
transition area between the conductor and insulation
crimps. Equal amounts of the conductor strands and
insulation needs to be visible in the transition area. The
insulation position ensures that the insulation is crimped
along the full length of the insulation crimp, and that no
insulation is crimped under the conductor crimp. The
insulation position is set by the wire stop and strip length
for bench applications. For automatic wire processing
applications, the insulation position is set by the in/out
press adjustment.
Strip Length
The strip length is determined by measuring the
exposed conductor strands after the insulation is
removed. The strip length determines the conductor
brush length when the insulation position is centered.
Figure 4-2
*Consult individual terminal specification requirements
Insulation Crimp Height
Molex does not specify insulation crimp heights
Process
because of the wide variety of insulation thickness,
material, and hardness. Most terminals are
designed to accommodate multiple wire ranges.
Within the terminal’s range, the strain relief may or
may not completely surround the diameter of the
wire. This condition will still provide an acceptable
insulation crimp for most applications.
1. A large strain relief should firmly grip at least
88% of the wire.
31.5
30.5
29.5
28.5
Example Control Chart
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25
Measurements
Figure 4-3
Sample
Contol Limit
Control Limit
Upper Specification
Lower Specification
2. A smaller strain relief should firmly grip at least
50% of the wire and firmly hold the top of the
wire.
The combination of people, equipment, tooling,
materials, methods, and procedures needed to produce
a crimp termination. Process Control is used to track
attributes over time to aid in the detection of change to
Order No: TM-638000029
Revision: D
Release Date: 09-04-03
Revision Date: 12-23-09
UNCONTROLLED COPY
Page 7 of 24
相关PDF资料 |
PDF描述 |
|---|---|
| 0011030043 | TOOL HAND EXTRACT MICROFIT 3.0 |
| 0011030044 | TOOL HAND EXTRACTION MINI-FIT JR |
| 0011184647 | 60758A102 COMBINATION ANVIL |
| 0011184779 | ANVIL |
| 0011184785 | CONDUCTOR ANVIL |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 0011030037 | 制造商:Molex 功能描述:Manual Extraction Tool 制造商:Molex 功能描述:HT60624 EXTRACTOR TOOL |
| 0011030039 | 制造商:Molex 功能描述:HT60646 EXTRACTOR-4296/-1 |
| 0011030043 | 功能描述:TOOL HAND EXTRACT MICROFIT 3.0 RoHS:否 类别:工具 >> 插入，抽取 系列:Micro-Fit 3.0™ 标准包装:1 系列:* 其它名称:0011-03-00080011-03-0008-E00110300080011030008-E11-03-0008-E1103000811030008-EQ4729393AT0980176A |
| 0011030044 | 功能描述:TOOL HAND EXTRACTION MINI-FIT JR RoHS:否 类别:工具 >> 插入，抽取 系列:Mini-Fit Jr™ 标准包装:1 系列:* 其它名称:0011-03-00080011-03-0008-E00110300080011030008-E11-03-0008-E1103000811030008-EQ4729393AT0980176A |
| 0011030045 | 功能描述:TOOL HOUSING EXTRACTION 1.25MM RoHS:否 类别:工具 >> 插入，抽取 系列:- 标准包装:1 系列:* 其它名称:0011-03-00080011-03-0008-E00110300080011030008-E11-03-0008-E1103000811030008-EQ4729393AT0980176A |
发布紧急采购，3分钟左右您将得到回复。