- 您现在的位置：买卖IC网 > PDF目录24705 > 06033C223KAT2A KONDENSATOR 22NF 25V 10ST PDF资料下载
参数资料
| 型号： | 06033C223KAT2A |
| 英文描述： | KONDENSATOR 22NF 25V 10ST |
| 中文描述： | KONDENSATOR 22NF 25V的10ST |
| 文件页数： | 32/46页 |
| 文件大小： | 659K |
| 代理商： | 06033C223KAT2A |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页当前第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页
37
General Description
Effects of Voltage – Variations in voltage have little effect
on Class 1 dielectric but does affect the capacitance and
dissipation factor of Class 2 dielectrics. The application of
DC voltage reduces both the capacitance and dissipation
factor while the application of an AC voltage within a
reasonable range tends to increase both capacitance and
dissipation factor readings. If a high enough AC voltage is
applied, eventually it will reduce capacitance just as a DC
voltage will. Figure 2 shows the effects of AC voltage.
Capacitor specifications specify the AC voltage at which to
measure (normally 0.5 or 1 VAC) and application of the
wrong voltage can cause spurious readings. Figure 3 gives
the voltage coefficient of dissipation factor for various AC
voltages at 1 kilohertz. Applications of different frequencies
will affect the percentage changes versus voltages.
The effect of the application of DC voltage is shown in
Figure 4. The voltage coefficient is more pronounced for
higher K dielectrics. These figures are shown for room tem-
perature conditions. The combination characteristic known
as voltage temperature limits which shows the effects of
rated voltage over the operating temperature range is
shown in Figure 5 for the military BX characteristic.
Cap. Change vs. D.C. Volts
AVX X7R T.C.
Typical Cap. Change vs. Temperature
AVX X7R T.C.
Effects of Time – Class 2 ceramic capacitors change
capacitance and dissipation factor with time as well as tem-
perature, voltage and frequency. This change with time is
known as aging. Aging is caused by a gradual re-alignment
of the crystalline structure of the ceramic and produces an
exponential loss in capacitance and decrease in dissipation
factor versus time. A typical curve of aging rate for semi-
stable ceramics is shown in Figure 6.
If a Class 2 ceramic capacitor that has been sitting on the
shelf for a period of time, is heated above its curie point,
(125°C for 4 hours or 150°C for 12 hour will suffice) the part
will de-age and return to its initial capacitance and dissi-
pation factor readings. Because the capacitance changes
rapidly, immediately after de-aging, the basic capacitance
measurements are normally referred to a time period some-
time after the de-aging process. Various manufacturers use
different time bases but the most popular one is one day
or twenty-four hours after “last heat.” Change in the aging
curve can be caused by the application of voltage and
other stresses. The possible changes in capacitance due to
de-aging by heating the unit explain why capacitance
changes are allowed after test, such as temperature cycling,
moisture resistance, etc., in MIL specs. The application of
high voltages such as dielectric withstanding voltages also
25%
50%
75%
100%
Percent Rated Volts
Capacitance
Change
Percent
2.5
0
-2.5
-5
-7.5
-10
0VDC
RVDC
-55 -35
-15
+5
+25 +45 +65 +85 +105 +125
Temperature Degrees Centigrade
Capacitance
Change
Percent
+20
+10
0
-10
-20
-30
Figure 2
50
40
30
20
10
0
12.5
25
37.5
50
Volts AC at 1.0 KHz
Capacitance
Change
Percent
Cap. Change vs. A.C. Volts
AVX X7R T.C.
Figure 3
Curve 3 - 25 VDC Rated Capacitor
Curve 2 - 50 VDC Rated Capacitor
Curve 1 - 100 VDC Rated Capacitor
Curve 3
Curve 2
Curve 1
.5
1.0
1.5
2.0
2.5
AC Measurement Volts at 1.0 KHz
Dissipation
Factor
Percent
10.0
8.0
6.0
4.0
2.0
0
D.F. vs. A.C. Measurement Volts
AVX X7R T.C.
Figure 4
Figure 5
相关PDF资料 |
PDF描述 |
|---|---|
| 06033G104ZAT2A | KONDENSATOR 100NF 25V 10ST |
| 06035A100JAT2A | KONDENSATOR 10PF 50V |
| 06035A101JAT2A | KONDENSATOR 50V 100PF 10ST |
| 06035A102JAT2A | KONDENSATOR 50V 1NF 10ST |
| 06035A220JAT2A | KONDENSATOR 50V 22PF 10ST |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 06033C223KAT2A/4K | 制造商:AVX Corporation 功能描述:CAP CER 0.022UF 25V 10% X7R 0603 |
| 06033C223KAT4A | 功能描述:多层陶瓷电容器MLCC - SMD/SMT 25volts 0.022uF 10% X7R RoHS:否 制造商:American Technical Ceramics (ATC) 电容:10 pF 容差:1 % 电压额定值:250 V 温度系数/代码:C0G (NP0) 外壳代码 - in:0505 外壳代码 - mm:1414 工作温度范围:- 55 C to + 125 C 产品:Low ESR MLCCs 封装:Reel |
| 06033C223K-MR | 制造商:TE Connectivity 功能描述:CAP. 22NF MINIREEL 500PCS |
| 06033C223M4T2A | 功能描述:多层陶瓷电容器MLCC - SMD/SMT 25volts 0.022uF 20% X7R RoHS:否 制造商:American Technical Ceramics (ATC) 电容:10 pF 容差:1 % 电压额定值:250 V 温度系数/代码:C0G (NP0) 外壳代码 - in:0505 外壳代码 - mm:1414 工作温度范围:- 55 C to + 125 C 产品:Low ESR MLCCs 封装:Reel |
| 06033C223MAT2A | 功能描述:多层陶瓷电容器MLCC - SMD/SMT 25volts 0.022uF 20% X7R RoHS:否 制造商:American Technical Ceramics (ATC) 电容:10 pF 容差:1 % 电压额定值:250 V 温度系数/代码:C0G (NP0) 外壳代码 - in:0505 外壳代码 - mm:1414 工作温度范围:- 55 C to + 125 C 产品:Low ESR MLCCs 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。