- 您现在的位置：买卖IC网 > PDF目录18847 > 0622019502 (Molex Inc)TOOL HOLDER 72MM VHDM BACKPLANE PDF资料下载
参数资料
| 型号： | 0622019502 |
| 厂商： | Molex Inc |
| 文件页数： | 8/23页 |
| 文件大小： | 0K |
| 描述： | TOOL HOLDER 72MM VHDM BACKPLANE |
| 标准包装： | 1 |
| 系列： | * |
| 其它名称： | 062201-9502 62201-9502 622019502 |
VHDM ? and VHDM-HSD ? *
2.1 Printed Circuit Board Support
The HSD / VHDM tooling requires up to 15 lb per pin of
force to press the connectors into the printed circuit
boards. Therefore, a backup or support is required to
prevent damage to the printed circuit boards. The
support fixture should have clearance for the connector
terminals when they protrude through the underside of
the printed circuit board. It is also recommended that
the support fixture have locating pins. Due to the
custom nature of each application, Molex does not
supply support and locating fixtures, the customer
normally supplies them.
The following is one simple way of making a printed
circuit board support and locating fixture:
*VHDM and VHDM HSD are Trademark of Teradyne, Inc
10. Press the connector into the p.c. board and observe
for any deflection of the board when the ram is at
the bottom of its stroke.
2.2 Press Stroke Adjustment
Most presses have some means of adjusting the stroke;
please refer to the appropriate manual (for the press
being used) for press stroke adjustments. The stroke
should be adjusted so that when the press ram stops in
the down position, the bottom of the connector is flush to
.155mm (.006 in.) above the surface of the printed circuit
board.
See Figure 2-1.
.155mm
(.006”)
Maximum
1. Locate a suitable piece of material for the backup. It
should be approximately 3/4 inch thick and same
size or a little larger than the printed circuit board to
be used. While aluminum could be used, a rigid
nonconductive material such as a phenolic is
preferred. (A stack of scrap p.c. boards of suitable
size could be fastened together and used.)
2. Obtain a scrap p.c. board like the ones to be
assembled. Attach this board to the material from
step 1.
3. Using an oversize drill bit, drill through each hole
where a pin from the connector will go. Drill deep
enough into the lower material to be certain the pins
do not bottom out when inserted (at least 5mm
[0.20in] deep).
4. Locate two (2) holes on the p.c. board to use as
locating points. Drill for and mount suitably sized
dowel pins in these two locations on the support
fixture.
Figure 2-1
MAXIMUM CLEARANCE WHEN
CONNECTOR FULLY SEATED
2.3 Installation
The only installation required is when you need to install
insertion modules into a tooling holder. To do this, use
the following procedure:
KEYWAY
5. Clear out the support for any components mounted
on the underside of the printed circuit board.
6 Place a p.c. board on top of the support, located by
Figure 2-2
TOOLING HOLDER
M3 SET SCREW
the two pins, and check that the holes for the
connector pins are aligned.
7. Pre-insert a connector in the p.c. board in the
correct position.
8. Insert the press-in tool of proper size into the
connector.
9. Place the support with p.c. board under the press
ram.
1. Along the lower edge of the tooling holder is a row of
M3 set screws, back these out so that they do not
protrude into the inside of the holder. See Figure 2-
2.
2. Slide the insertion modules into the tooling holder in
the proper order. See Figure 2-3. The modules are
keyed so that they cannot be put in backwards.
Doc. No: TM-622010999
Revision: H
Release Date: 08-10-99
Revision Date: 03-15-10
UNCONTROLLED COPY
Page 8 of 23
相关PDF资料 |
PDF描述 |
|---|---|
| ABS1412419 | SWITCH TURQ SPDT HINGE GOLD SLD |
| 9171-24 BLK | PATCHCORD SQ SCKT-PIN PLUG BLK |
| 0622022580 | TOOL INSERT 3POS 1-UP POWER MOD |
| ABS1411419 | SWITCH TURQ SPDT HINGE GOLD SLD |
| AT 5 B10 | SENSOR CURRENT 5A MOD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 0622019503 | 功能描述:TOOL HOLDER 156MM VHDM BACKPLANE RoHS:是 类别:工具 >> 压接器，施用器，压力机 - 配件 系列:* 标准包装:1 系列:- 其它名称:512A512A-NDQ1137690B |
| 0622019504 | 功能描述:TOOL HOLDER 216MM VHDM BACKPLANE RoHS:是 类别:工具 >> 压接器，施用器，压力机 - 配件 系列:* 标准包装:1 系列:- 其它名称:512A512A-NDQ1137690B |
| 0622019505 | 功能描述:5 X 6 HEADER INSERTION MODULE RoHS:否 类别:工具 >> 插入，抽取 系列:* 标准包装:1 系列:* 其它名称:0011-03-00080011-03-0008-E00110300080011030008-E11-03-0008-E1103000811030008-EQ4729393AT0980176A |
| 0622019506 | 功能描述:5 X 12 HEADER INSERTION MODULE RoHS:否 类别:工具 >> 插入，抽取 系列:* 标准包装:1 系列:* 其它名称:0011-03-00080011-03-0008-E00110300080011030008-E11-03-0008-E1103000811030008-EQ4729393AT0980176A |
| 0622019507 | 功能描述:5 X 24 HEADER INSERTION MODULE RoHS:否 类别:工具 >> 插入，抽取 系列:* 标准包装:1 系列:* 其它名称:0011-03-00080011-03-0008-E00110300080011030008-E11-03-0008-E1103000811030008-EQ4729393AT0980176A |
发布紧急采购，3分钟左右您将得到回复。