- 您现在的位置：买卖IC网 > PDF目录21941 > 0622022009 (Molex Inc)TOOL BLOCK SPACER - SIGNAL HDRS PDF资料下载
参数资料
| 型号： | 0622022009 |
| 厂商： | Molex Inc |
| 文件页数： | 7/28页 |
| 文件大小： | 0K |
| 描述： | TOOL BLOCK SPACER - SIGNAL HDRS |
| 标准包装： | 1 |
| 系列： | * |
| 其它名称： | 062202-2009 62202-2009 622022009 |
第1页第2页第3页第4页第5页第6页当前第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
GbX ? Backplane and Daughtercard Tooling
*GbX ? is a Trademark of Amphenol Corp.
2.1
Printed Circuit Board Support
The GbX ? tooling requires up to 10 lb. per pin of
force to press the connectors into the printed circuit
10. Press the connector into the P.C. board and
observe for any deflection of the board when the
ram is at the bottom of its stroke.
boards. Therefore, a backup or support is required
to prevent damage to the P.C. board. The support
fixture should have clearance for the connector
terminals when they protrude through the underside
of the P.C. board. It is also recommended that the
support fixture have locating pins. Due to the
custom nature of each application, Molex does not
supply support and locating fixtures, the customer
normally supplies them.
The following is one simple way of making a P.C.
board support and locating fixture:
1. Locate a suitable piece of material for the
backup. It should be approximately 3/4 inch
thick and same size or a little larger than the
printed circuit board to be used. While
aluminum could be used, a rigid nonconductive
material such as a phenolic is preferred. (A
stack of scrap P.C. boards of suitable size could
be fastened together and used.)
2. Obtain a scrap P.C. board like the ones to be
assembled. Attach this board to the material
from step 1.
3. Using an oversize drill bit, drill through each
hole where a pin from the connector will go.
Drill deep enough into the lower material to be
certain the pins do not bottom out when inserted
(at least 5mm [0.20in] deep).
4. Locate two (2) holes on the P.C. board to use as
locating points. Drill for and mount suitably
sized dowel pins in these two locations on the
support fixture.
5. Clear out the support for any components
mounted on the underside of the printed circuit
board.
2.2
2.3
Press Stroke Adjustment
Most presses have some means of adjusting the
stroke; please refer to the appropriate manual (for
the press being used) for press stroke adjustments.
The stroke should be adjusted so that when the
press ram stops in the down position, the bottom of
the connector is flush to .25mm (.010 in.) above the
surface of the P.C. board. See Figure 2-1.
.25mm
(.010 in.)
Max.
Figure 2-1
MAXIMUM CLEARANCE WHEN
CONNECTOR FULLY SEATED
Installation
The only installation required is when you need to
install insertion modules into a tooling holder. To
do this, use the following procedure:
1. Along the lower edge of the tooling holder is a
row of M3 set screws, (See Figure 2-2), back
these out so that they do not protrude into the
inside of the holder.
KEYWAY
6 Place a P.C. board on top of the support,
located by the two pins, and check that the
holes for the connector pins are aligned.
Figure 2-2
TOOLING HOLDER
M3 SET SCREW
7. Pre-insert a connector in the P.C. board in the
correct position.
8. Insert the press-in tool of proper size into the
connector.
9. Place the support with the P.C. board under the
press ram.
2. Slide the insertion modules into the tooling
holder in the proper order. See Figure 2-3.
The modules are keyed so that they cannot be
put in backwards.
Doc. No: TM-622022099
Revision: H
Release Date: 06-23-04
Revision Date: 01-28-11
UNCONTROLLED COPY
Page 7 of 28
相关PDF资料 |
PDF描述 |
|---|---|
| AH175-WG-7-B | IC HALL SENSOR BIPO 25MA SC59-3 |
| AH175-WG-7-B | IC HALL SENSOR BIPO 25MA SC59-3 |
| FK2125T407AL-T | FILTER EMI 400MHZ 100MA 0805 |
| D32G-016.368M | OSC TCXO 16.368 MHZ 3.3V SMD |
| MAX2363ETM+T | IC TRANSMITTER QUAD 48TQFN-EP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 0622022010 | 功能描述:TOOL INSERTION 40POS 4ROWS RoHS:是 类别:工具 >> 压接器，施用器，压力机 - 配件 系列:* 标准包装:1 系列:- 其它名称:512A512A-NDQ1137690B |
| 0622022015 | 功能描述:TOOL INSERT 20POS 4ROWS L SERIES RoHS:是 类别:工具 >> 压接器，施用器，压力机 - 配件 系列:* 标准包装:1 系列:- 其它名称:512A512A-NDQ1137690B |
| 0622022020 | 功能描述:TOOL INSERTION 50POS 4ROWS RoHS:是 类别:工具 >> 压接器，施用器，压力机 - 配件 系列:* 标准包装:1 系列:- 其它名称:512A512A-NDQ1137690B |
| 0622022025 | 功能描述:TOOL INSERT 40POS 4ROWS L SERIES RoHS:是 类别:工具 >> 压接器，施用器，压力机 - 配件 系列:* 标准包装:1 系列:- 其它名称:512A512A-NDQ1137690B |
| 0622022026 | 功能描述:INSERT TOOL 4X25 制造商:molex, llc 系列:* 零件状态:有效 标准包装:1 |
发布紧急采购，3分钟左右您将得到回复。