- 您现在的位置：买卖IC网 > Datasheet目录567 > 0638007900 (Molex Inc)TOOL PRESS SHUT HEIGHT GAUGE Datasheet资料下载
参数资料
| 型号： | 0638007900 |
| 厂商： | Molex Inc |
| 文件页数： | 2/4页 |
| 文件大小： | 0K |
| 描述： | TOOL PRESS SHUT HEIGHT GAUGE |
| 标准包装： | 1 |
| 附件类型： | 闭合高度量规 |
| 适用于相关产品： | 台式压机 |
| 配用： | WM3459-ND - TM3000 220V/50HZ PRESS TO 10AWG WM6378-ND - PRESS TM4000 UP TO 4AWG 240AC WM4793-ND - CRMP PRESS TM3000 120V TO 10AWG |
| 其它名称： | 063800-7900 0638007900-ND 63800-7900 638007900 WM6296 |
Press Shut Height Gauge
6. Hand cycle the press ram down. As it approaches it lowest point
(BDC), the ram will touch the cap and press it down, causing the
pointer on the dial indicator to turn clockwise.
WARNING: NEVER cycle the press ram under power when
measuring shut height.
NOTE: Flywheel-driven presses should be hand-cycled using a
socket wrench with a breaker bar. As the ram approaches BDC,
continue to turn the flywheel while reading the gauge. If the flywheel
stops turning near BDC, the upward force of the shut height gauge
may cause the press to become locked.
NOTE: The shut height on some presses may be easier to measure
if two operators are used (one to hand-cycle the press, one to read
the dial indicator)
7. When the pointer stops turning clockwise, the press ram is at shut
height (BDC). If the pointer stops at “0”, then the press shut height is
PRESS
RAM
CAP
PRESS
BASE PLATE
Figure 2
(PRESS GUARDS NOT SHOWN)
exactly 135.8mm (5.346 in). If the pointer stops away from “0” in a clockwise direction, then the press
shut height is less than 135.8mm. Similarly, if the pointer stops away from “0” in a counterclockwise
direction, then the press shut height is more than 135.8mm. See Figure 3.
8. To read the shut height difference from “0”, each line on the face of the dial indicator represents 0.01mm
(0.0004 in) of travel. See Figure 3.
Shut height is
more than 135.8mm
Shut height is
less than 135.8mm
In this case,
Press shut height = 135.8 + (11 x 0.01) = 135.91mm
Figure 3
9. Hand-cycle the press ram back to its highest position (TDC).
10. If necessary, adjust the press shut height per the manufacturer’s procedure. After adjustment, re-measure the
press shut height.
Doc No: ATS-638007900
Revision: e
Release Date: 09-03-09
Revision Date: 11-22-13
UNCONTROLLED COPY
Page 2 of 4
相关PDF资料 |
PDF描述 |
|---|---|
| 0638013501 | AIR-FEED ASSY |
| 0638013901 | CONDUCTOR PUNCH |
| 0638013903 | INSULATION PUNCH |
| 0638014100 | MINI MAC APPLICATOR - REAR FEED |
| 0638014300 | MINI MAC APPLICATOR - REAR FEED |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 0638007901 | 功能描述:CAP 制造商:molex, llc 系列:* 零件状态:在售 标准包装:1 |
| 0638007905 | 功能描述:COVER 制造商:molex, llc 系列:* 零件状态:在售 标准包装:1 |
| 0638007950 | 制造商:Molex 功能描述:CRIMP FORCE MONITOR-TM3000/4001 |
| 0638007952 | 功能描述:FORCE SENSOR RAM MNTD 制造商:molex, llc 系列:* 零件状态:有效 标准包装:1 |
| 0638007953 | 功能描述:SENSOR CABLE 制造商:molex, llc 系列:* 零件状态:有效 标准包装:1 |
发布紧急采购，3分钟左右您将得到回复。