- 您现在的位置：买卖IC网 > Datasheet目录568 > 0638027600 (Molex Inc)MINI MAC APPLICATOR 14-16 AWG Datasheet资料下载
参数资料
| 型号： | 0638027600 |
| 厂商： | Molex Inc |
| 文件页数： | 2/5页 |
| 文件大小： | 0K |
| 描述： | MINI MAC APPLICATOR 14-16 AWG |
| 标准包装： | 1 |
| 系列： | Mini-Mac™, Krimptite™ |
| 工具类型： | 台式压机，施用器 |
| 适用于相关产品： | 快速连接端子，14-16 AWG |
| 配用： | 0190080031-ND - .250X.032 FLAG QD KRIMP./REEL 0190080028-ND - .187X.020 FLAG QD KRIMP./REEL 0190080029-ND - .187X.032 FLAG QD KRIMP./REEL |
| 相关产品： | WM3459-ND - TM3000 220V/50HZ PRESS TO 10AWG WM6378-ND - PRESS TM4000 UP TO 4AWG 240AC WM4793-ND - CRMP PRESS TM3000 120V TO 10AWG |
| 其它名称： | 063802-7600 63802-7600 638027600 |
Rear Feed Applicator for Flag Krimptite ? Quick Disconnect Female Terminals
CRIMP SPECIFICATIONS
Terminal Order No. Terminal Eng. No.
Wire Size
Conductor Crimp Height
Mean Go No Go
Pull Force
Minimum
AWG
mm2
mm In. mm In. mm In.
N Lb.
19008-0028
19008-0029
19008-0031
BBZ-1148
BBZ-1148-032
BBZ-1159
14
16
14
16
14
16
2.00
1.30
2.00
1.30
2.00
1.30
1.55 .061 1.42 .056 1.68
1.55 .061 1.42 .056 1.68
1.55 .061 1.42 .056 1.68
.066
.066
.066
222.4 50.0
133.4 30.0
222.4 50.0
133.4 30.0
222.4 50.0
133.4 30.0
Seam
Seam shall not be open and no wire allowed out of the crimping
Pull Force should be measured with no influence from the insulation crimp. The above specifications are
guidelines to an optimum crimp.
Tool Calibration
To recalibrate this applicator, make sure the power is
completely shut off on the press.
1. The Applicator must be properly installed in the press.
2. Crimping dies must be properly installed in the Applicator.
3. The recommended method of measuring the crimp height
of the conductor dies is the soft metal slug method. See
CONDUCTOR
CRIMP DIE
E2
USE SOFT METAL
SLUG METHOD
Figure 1.
4. The slug must have a diameter 0.51mm (.020”) larger
than the “X” No Go dimension before crimping.
5. Place the soft metal slug (solder) into the nest of the
bottom die and crimp (by hand cycling the press) similar
to a terminal. The crimp height can be measured with a
blade type micrometer or dial caliper, (Dimension “X”).
6. Adjustment of the crimp height can be accomplished by
indexing the conductor cam. The letter “A” gives the
loosest position and “K” gives the tightest position. A
total adjustment of 0.50mm (.020”) can be achieved by
“X” CRIMP
HEIGHT
E1
CRIMP PROFILE
Use soft metal slug (solder) method to
Measure the “X” dimension. Verify tooling
crimp height calibration by referring to the
Go/No Go dimensions shown in the chart.
Figure 1
adjusting the conductor cam.
Note: If the crimp height is too tight on the setting “A”, check the shut height of the press. See the Industrial Mini-
Mac Applicator Manual Section 2.1 for adjustments.
Molex does not sell gauge pins contact your local industrial supplier.
Doc No: ATS-638027600
Revision: B
Release Date: 08-20-09
Revision Date: 01-13-11
UNCONTROLLED COPY
Page 2 of 5
相关PDF资料 |
PDF描述 |
|---|---|
| 0638027700 | MINI MAC APPLICATOR - REAR FEED |
| 0638032301 | ANVIL |
| 0638032302 | INSULATION PUNCH |
| 0638042000 | MINI MAC APPLICATOR - REAR FEED |
| 0638060600 | MINI MAC APPLICATOR - REAR FEED |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 0638027670 | 制造商:Molex 功能描述:TOOL KIT 制造商:Molex 功能描述:TOOL KIT - Bulk |
| 0638027700 | 功能描述:MINI MAC APPLICATOR - REAR FEED RoHS:否 类别:工具 >> 压接器，施用器，压力机 系列:* 产品培训模块:Board-to-Wire Connectors 标准包装:1 系列:DF11 工具类型:台式压机，施用器 适用于相关产品:矩形触点，24-28 AWG 特点:- 配用:H1505TR-ND - CONN SOCKET 24-28AWG CRIMP GOLDH1504TR-ND - CONN SOCKET 24-28AWG CRIMP TIN 相关产品:AP105-DF11-2428S(64)-ND - TOOL APPLICATOR DF11 ACCESSORIESAP105-DF11-2428S(63)-ND - TOOL APPLICATOR DF11 ACCESSORIESAP105-DF11-2428S(62)-ND - TOOL APPLICATOR DF11 ACCESSORIESAP105-DF11-2428S(61)-ND - TOOL APPLICATOR DF11 ACCESSORIESCM-105 WITH TRANSFORMER-ND - TOOL AUTO CRIMPING MACHINE 其它名称:*AP105-DF11-2428SQ1139807AQ949366 |
| 0638027770 | 制造商:Molex 功能描述:TOOL KIT 制造商:Molex 功能描述:TOOL KIT - Bulk |
| 0638031070 | 制造商:Molex 功能描述:TOOL KIT 制造商:Molex 功能描述:TOOL KIT - Bulk |
| 0638031170 | 制造商:Molex 功能描述:TOOL KIT 制造商:Molex 功能描述:TOOL KIT - Bulk |
发布紧急采购，3分钟左右您将得到回复。