- 您现在的位置：买卖IC网 > Datasheet目录573 > 0638237500 (Molex Inc)HANDTOOL CRIMP 2.5MM 22-28AWG Datasheet资料下载
参数资料
| 型号： | 0638237500 |
| 厂商： | Molex Inc |
| 文件页数： | 3/7页 |
| 文件大小： | 0K |
| 描述： | HANDTOOL CRIMP 2.5MM 22-28AWG |
| 标准包装： | 5 |
| 系列： | PremiumGrade™ |
| 工具类型： | 手动压接器 |
| 适用于相关产品： | 50752-8000，50752-8100 |
| 特点： | 侧面插入，棘齿 |
| 相关产品： | WM5196-ND - LOCATOR ASSEMBLY FOR 0638237500 |
| 其它名称： | 063823-7500 63823-7500 638237500 WM5195 |
Hand Crimp Tool for 2.50mm (.098”) Wire-to-Board Crimp Terminals
2. Insert the terminal into the correct profile until the terminal is fully seated and stops. Make sure the wire
stop blade is fully seated on the terminal behind the conductor grip section.
3. Gently pivot the locator closed.
4. Bring down the wire stop blade.
5. Slide the pre-stripped wire into the terminal; make sure to aim the wire brush towards the tip point on the
wire stop blade. See Figure 2. Align the wire so that it is parallel and sitting into the terminal. Maintain a
light and constant pressure on the wire that is seated in the terminal at all times. (Do not let go of the
wire.) Be sure to hold the wire and terminal in place until the terminal is fully crimped. See Figure 3.
6. Close the tool until the ratchet releases.
7. Lift the wire stop blade up.
8. Carefully remove the crimped terminal.
Note: To maintain good brush control and a consistent bell mouth the crimping instructions must be
followed.
CONDUCTOR
WIRE STOP
BLADE
TERMINAL
CONDUCTOR
PUNCH
WIRE STOP
BLADE
PUNCH
INSULATION
LOCATOR
PUNCH
WIRE
Figure 3
WIRE
Figure 2
TERMINAL
CONDUCTOR
ANVIL
INSULATION
ANVIL
Note: The tamper proof ratchet action will not release the tool until it has been fully closed.
Note: To maintain good brush control and a consistent bell mouth the crimping instructions must be followed.
Terminal Locator Replacement/Change Over
This section describes the procedure for changing locators.
Removal
1. With the tool in the open position, pivot the terminal locator outward.
2. Remove the M4 BHCS. See Figure 4.
Installation
1. Place the proper locator, (See Chart on page 2), on the hand tool.
Install the M4 BHCS. See Figure 4.
2. Tighten the screw enough to hold the locator. Make sure the
locator can still float freely with hand pressure.
M4 BHCS
Figure 4
PIVOT LOCATOR
Doc No: ATS-6382375HM
Revision: B
Release Date: 09-27-10
Revision Date: 10-14-10
UNCONTROLLED COPY
Page 3 of 7
相关PDF资料 |
PDF描述 |
|---|---|
| 0638237900 | HANDTOOL CRIMP BOARD-IN 22-28AWG |
| 0638238000 | HANDTOOL CRIMP 2.5MM WW 22-28AWG |
| 0638238270 | TOOL MOD HEAD CRIMP 0638238200 |
| 0638238370 | CRIMP MODULE HEAD FOR 0638238300 |
| 0638238400 | HAND CRIMP TOOL |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 0638237570 | 制造商:Molex 功能描述:MODULAR CRIMP HEAD - Bulk |
| 0638237575 | 功能描述:LOCATOR ASSEMBLY FOR 0638237500 RoHS:是 类别:工具 >> 压接器，施用器，压力机 - 配件 系列:- 标准包装:1 系列:- 其它名称:512A512A-NDQ1137690B |
| 0638237670 | 功能描述:CRIMP TOOL KIT FOR CP 06 制造商:molex, llc 系列:PremiumGrade??，CMC 零件状态:在售 工具类型:模具组套 配套使用产品/相关产品:矩形触点，18-20 AWG 规格:- 兼容工具:63810-1060 电缆组:- 标准包装:100 |
| 0638237770 | 功能描述:CRIMP TOOL KIT FOR CP 15 制造商:molex, llc 系列:PremiumGrade??，CMC 零件状态:在售 工具类型:模具组套 配套使用产品/相关产品:矩形触点，16-18 AWG 规格:- 兼容工具:63810-1060 电缆组:- 标准包装:100 |
| 0638237870 | 功能描述:CRIMP TOOL KIT FOR JAE 制造商:molex, llc 系列:PremiumGrade?? 零件状态:在售 工具类型:模具组套 配套使用产品/相关产品:矩形触点，20 AWG 规格:- 兼容工具:63810-1060 电缆组:- 标准包装:100 |
发布紧急采购，3分钟左右您将得到回复。