- 您现在的位置：买卖IC网 > PDF目录19184 > 0639002600 (Molex Inc)FINE ADJUST APPLICATOR PDF资料下载
参数资料
| 型号： | 0639002600 |
| 厂商： | Molex Inc |
| 文件页数： | 7/24页 |
| 文件大小： | 0K |
| 描述： | FINE ADJUST APPLICATOR |
| RoHS指令信息： | 0639002600 Cert of Compliance |
| 标准包装： | 1 |
| 系列： | FineAdjust™, Mini-Fit™ |
| 工具类型： | 台式压机，施用器 |
| 适用于相关产品： | 矩形触点，18-24 AWG |
| 配用： | WM7081CT-ND - CONN PIN HCS 18-20AWG GOLD WM6890CT-ND - CONN SOCKET 18-24AWG CRIMP GOLD WM6697TR-ND - CONN PIN 18-20AWG TIN CRIMP WM7539-ND - CONN SCKT TERM HCS 18-20AWG GOLD WM7081TR-ND - CONN PIN HCS 18-20AWG GOLD WM6890TR-ND - CONN SOCKET 18-24AWG CRIMP GOLD WM6697CT-ND - CONN PIN 18-20AWG TIN CRIMP WM18521CT-ND - CONN TERM MALE 18-24AWG GOLD WM1017CT-ND - CONN TERM MALE 18-24AWG TIN WM2985TR-ND - TERM PIN TIN 18-24AWG TIN 更多... |
| 相关产品： | WM3459-ND - TM3000 220V/50HZ PRESS TO 10AWG WM6378-ND - PRESS TM4000 UP TO 4AWG 240AC WM4793-ND - CRMP PRESS TM3000 120V TO 10AWG |
| 其它名称： | 063900-2600 63900-2600 639002600 WM3460 |
Quality Crimp Handbook
To evaluate the insulation crimp section, cut the wire
Cut-off Tab Length
This material protrudes outside the insulation crimp
after the terminal is separated from the carrier strip.
As a rule, the cut-off tab is approximately 1.0 to 1.5
times terminal material thickness. * A cut-off tab
that is too long may expose a terminal outside the
housing or it may fail electrical spacing
requirements. In most situations, a tool is set - up to
provide a cut-off tab that is flush to one material
thickness.
Extrusions (Flash)
These small flares form on the bottom of the
conductor crimp resulting from the clearance
between the punch and anvil tooling. If the anvil is
worn or the terminal is over-crimped, excessive
extrusion is the results. An uneven extrusion may
also result if the punch and anvil alignment is not
correct, if the feed adjustment is off, or if there is
insufficient/excessive terminal drag.
Insulation Crimp (Strain Relief)
This is the part of the terminal that provides wire
support for insertion into the housing. It also allows
the terminal to withstand shock and vibration. The
terminal needs to hold the wire as firmly as possible
without cutting through to the conductor strands.
The acceptability of an insulation crimp is subjective
and depends on the application. A bend test is
recommended to determine whether the strain relief
is acceptable for each particular application.
flush with the back of the terminal. Once the optimum
setting for the application is determined, it is important to
document the insulation crimp height. Then, as part of
the setup procedure, the operator can check the crimp
height.
Insulation Position
This is the location of the insulation in relation to the
transition area between the conductor and insulation
crimps. Equal amounts of the conductor strands and
insulation needs to be visible in the transition area. The
insulation position ensures that the insulation is crimped
along the full length of the insulation crimp, and that no
insulation is crimped under the conductor crimp. The
insulation position is set by the wire stop and strip length
for bench applications. For automatic wire processing
applications, the insulation position is set by the in/out
press adjustment.
Strip Length
The strip length is determined by measuring the
exposed conductor strands after the insulation is
removed. The strip length determines the conductor
brush length when the insulation position is centered.
Figure 4-2
*Consult individual terminal specification requirements
Insulation Crimp Height
Molex does not specify insulation crimp heights
Process
because of the wide variety of insulation thickness,
material, and hardness. Most terminals are
designed to accommodate multiple wire ranges.
Within the terminal’s range, the strain relief may or
may not completely surround the diameter of the
wire. This condition will still provide an acceptable
insulation crimp for most applications.
1. A large strain relief should firmly grip at least
88% of the wire.
31.5
30.5
29.5
28.5
Example Control Chart
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25
Measurements
Figure 4-3
Sample
Contol Limit
Control Limit
Upper Specification
Lower Specification
2. A smaller strain relief should firmly grip at least
50% of the wire and firmly hold the top of the
wire.
The combination of people, equipment, tooling,
materials, methods, and procedures needed to produce
a crimp termination. Process Control is used to track
attributes over time to aid in the detection of change to
Order No: TM-638000029
Revision: D
Release Date: 09-04-03
Revision Date: 12-23-09
UNCONTROLLED COPY
Page 7 of 24
相关PDF资料 |
PDF描述 |
|---|---|
| 88970033 | CONTROL LOGIC 12I/O 120V DIN MNT |
| 552-3511F | LED 5MM RED/GRN BICLR 3LEAD |
| DP06 | PIANO STYLE DIP SWITCH |
| ASDM1-25.000MHZ-LC-T | OSC MEMS 25.000 MHZ 3.3V SMD |
| 0639005200 | TOOL APPLICATOR 24-30AWG CRIMP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 0639002670 | 功能描述:TOOL KIT RoHS:是 类别:工具 >> 压接器，施用器，压力机 - 配件 系列:* 标准包装:1 系列:- 其它名称:512A512A-NDQ1137690B |
| 0639002700 | 功能描述:TOOL APPLICATOR CRIMP RoHS:是 类别:工具 >> 压接器，施用器，压力机 系列:FineAdjust™, Mini-Fit Jr™, Mini-Fit Plus™ 产品培训模块:Board-to-Wire Connectors 标准包装:1 系列:DF11 工具类型:台式压机，施用器 适用于相关产品:矩形触点，24-28 AWG 特点:- 配用:H1505TR-ND - CONN SOCKET 24-28AWG CRIMP GOLDH1504TR-ND - CONN SOCKET 24-28AWG CRIMP TIN 相关产品:AP105-DF11-2428S(64)-ND - TOOL APPLICATOR DF11 ACCESSORIESAP105-DF11-2428S(63)-ND - TOOL APPLICATOR DF11 ACCESSORIESAP105-DF11-2428S(62)-ND - TOOL APPLICATOR DF11 ACCESSORIESAP105-DF11-2428S(61)-ND - TOOL APPLICATOR DF11 ACCESSORIESCM-105 WITH TRANSFORMER-ND - TOOL AUTO CRIMPING MACHINE 其它名称:*AP105-DF11-2428SQ1139807AQ949366 |
| 0639002770 | 功能描述:TOOL KIT RoHS:是 类别:工具 >> 压接器，施用器，压力机 - 配件 系列:* 标准包装:1 系列:- 其它名称:512A512A-NDQ1137690B |
| 0639002800 | 功能描述:TOOL APPLICATOR CRIMP RoHS:是 类别:工具 >> 压接器，施用器，压力机 系列:FineAdjust™，Mini-Fit Jr™，Mini-Fit HCS™，Mini-Fit Plus HCS™ 产品培训模块:Board-to-Wire Connectors 标准包装:1 系列:DF11 工具类型:台式压机，施用器 适用于相关产品:矩形触点，24-28 AWG 特点:- 配用:H1505TR-ND - CONN SOCKET 24-28AWG CRIMP GOLDH1504TR-ND - CONN SOCKET 24-28AWG CRIMP TIN 相关产品:AP105-DF11-2428S(64)-ND - TOOL APPLICATOR DF11 ACCESSORIESAP105-DF11-2428S(63)-ND - TOOL APPLICATOR DF11 ACCESSORIESAP105-DF11-2428S(62)-ND - TOOL APPLICATOR DF11 ACCESSORIESAP105-DF11-2428S(61)-ND - TOOL APPLICATOR DF11 ACCESSORIESCM-105 WITH TRANSFORMER-ND - TOOL AUTO CRIMPING MACHINE 其它名称:*AP105-DF11-2428SQ1139807AQ949366 |
| 0639002870 | 功能描述:TOOL KIT RoHS:是 类别:工具 >> 压接器，施用器，压力机 - 配件 系列:* 标准包装:1 系列:- 其它名称:512A512A-NDQ1137690B |
发布紧急采购，3分钟左右您将得到回复。