- 您现在的位置：买卖IC网 > Datasheet目录586 > 0640030100 (Molex Inc)TOOL CRIMP WIREPIN TERM 10-22AWG Datasheet资料下载
参数资料
| 型号： | 0640030100 |
| 厂商： | Molex Inc |
| 文件页数： | 12/15页 |
| 文件大小： | 0K |
| 描述： | TOOL CRIMP WIREPIN TERM 10-22AWG |
| 其它有关文件： | Overlap Style Insulation Crimps |
| 产品目录绘图： | Premium Crimp Tool |
| 标准包装： | 1 |
| 系列： | Krimptite™, Versakrimp™ |
| 工具类型： | 手动压接器 |
| 适用于相关产品： | 接片和端子，10-22 AWG |
| 特点： | 侧面插入，棘齿 |
| 产品目录页面： | 364 (CN2011-ZH PDF) |
| 配用： | 0192070001-ND - PARALLEL SPLICE VERSAKRIMP 0191410063-ND - SPADE KRIMPTITE (BB-127-08) 0191410056-ND - SPADE KRIMPTITE (BB-124-06) 0191470062-ND - BLOCK SPADE VERSAKRIMP 0191410024-ND - SPADE KRIMPTITE (AA-135-10) 0191410020-ND - SPADE KRIMPTITE (AA-135-06) 0191410022-ND - SPADE KRIMPTITE (AA-135-08) 0191470057-ND - BLOCK SPADE VERSAKRIMP 0191470090-ND - BLOCK SPADE VERSAKRIMP 0191410065-ND - SPADE KRIMPTITE (BB-127-10) 更多... |
| 其它名称： | 064003-0100 064003-0100-E 0640030100-E 64003-0100 64003-0100-E 640030100 640030100-E WM9974 |
RHT-1992 Hand Crimp Tool
5. When crimping butt splices, the locator must be removed. Insert
the wire into the butt splice. Position the splice and the wire in
proper coded nest with conductor crimp on the conductor barrel
of the splice. The splice should be approximately centered
inside the tooling nests. See Figure 4. Cycle the tool.
6. When crimping parallel splices, the locator must be removed.
Insert the 1 st wire into one end of splice then insert the 2 nd wire
into the opposite end of the parallel splice. This procedure will
crimp both wires at the same time. Make sure the wires are fully
seated into the parallel splice. Position the splice and the wires
in proper coded nest with conductor crimp on the conductor
LUBRICATION POINTS
BOTH SIDES)
LIGHT OIL
(EVERY 3 MONTHS OR
5,000 CRIMPS)
Figure 6
barrel of the splice. The splice should be approximately
centered inside the tooling nests (See Figure 5). Cycle the tool.
Maintenance
It is recommended that each operator of the tool be made aware of, and responsible for, the following
maintenance steps:
1. Remove dust, moisture and other contaminants with a clean brush, or soft, lint-free cloth.
2. Do not use any abrasive materials that could damage the tool.
3. Make certain all pins; pivot points and bearing surfaces are protected with a thin coat of high quality machine
oil. Do not oil excessively. This tool was engineered for durability, but like any fine piece of equipment, it
needs cleaning and lubrication for a maximum service life of trouble-free crimping. A light oil, such as 30
weight automotive oil used at the oil points shown in Figure 6, every 5,000 crimps or 3 months will significantly
enhance the tool life and ensure a stable calibration.
4. When tool is not in use, keep the handles closed to prevent objects from becoming lodged in the crimping dies,
and store the tool in a clean, dry area.
Note : Whenever crimping without the locator, make sure the seam of the terminal is oriented up or down in the
tool if using unbrazed product, as this will provide higher pull force values.
Miscrimps or Jams
Should this tool ever become stuck or jammed in a
partially closed position, Do Not force the handles
open or closed. The tool will open easily by
pressing the ratchet release lever. See Figure 7.
How to Adjust Tool Preload (See Figure 7)
RATCHET
PRELOAD
TEST POINT
1.00
Over the life of the tool, it may be necessary to
adjust tool handle preload force. Listed below are
the steps required to adjust the crimping force of
RELEASE LEVER
PUSH UP
PRELOAD
ADJUSTMENT
LOCKING SCREW
PRELOAD
TEST POINT
1.00
the hand tool to obtain proper crimp conditions:
Figure 7
1. Remove the screw and plastic cover washer.
Note the setting wheel position.
2. Lift the setting wheel off the axle. Turn the eccentric axle with a screwdriver.
3. Turning the eccentric axle counter-clockwise (CCW) will increase handle force.
Doc No: ATS- 640030100
Revision: J
Release Date: 10-03-02
Revision Date: 08-08-13
UNCONTROLLED COPY
Page 12 of 15
相关PDF资料 |
PDF描述 |
|---|---|
| 0640033600 | HAND TOOL |
| 0640033700 | HAND TOOL |
| 0640050200 | AT-1991 CRIMP TOOL HEAD |
| 0640050300 | AT-1993 CRIMP TOOL HEAD |
| 0640050400 | AT-1994 CRIMP TOOL HEAD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 0640030170 | 制造商:Molex 功能描述:Tooling Kit For Hand Crimp Tool 制造商:Molex 功能描述:RHT/AT TOOL KIT - Bulk |
| 0640030200 | 功能描述:RHT-1997 HAND TOOL RoHS:否 类别:工具 >> 压接器，施用器，压力机 系列:* 产品培训模块:Board-to-Wire Connectors 标准包装:1 系列:DF11 工具类型:台式压机，施用器 适用于相关产品:矩形触点，24-28 AWG 特点:- 配用:H1505TR-ND - CONN SOCKET 24-28AWG CRIMP GOLDH1504TR-ND - CONN SOCKET 24-28AWG CRIMP TIN 相关产品:AP105-DF11-2428S(64)-ND - TOOL APPLICATOR DF11 ACCESSORIESAP105-DF11-2428S(63)-ND - TOOL APPLICATOR DF11 ACCESSORIESAP105-DF11-2428S(62)-ND - TOOL APPLICATOR DF11 ACCESSORIESAP105-DF11-2428S(61)-ND - TOOL APPLICATOR DF11 ACCESSORIESCM-105 WITH TRANSFORMER-ND - TOOL AUTO CRIMPING MACHINE 其它名称:*AP105-DF11-2428SQ1139807AQ949366 |
| 0640030270 | 功能描述:RHT/AT 1997 TOOL KIT RoHS:否 类别:未定义的类别 >> 其它 系列:* 标准包装:1 系列:* 其它名称:MS305720A |
| 0640030275 | 制造商:Molex 功能描述:LOCATOR ASSEMBLY 制造商:Molex 功能描述:LOCATOR ASSEMBLY - Bulk |
| 0640030400 | 功能描述:RHT-1753 HAND TOOL RoHS:否 类别:工具 >> 压接器，施用器，压力机 系列:* 产品培训模块:Board-to-Wire Connectors 标准包装:1 系列:DF11 工具类型:台式压机，施用器 适用于相关产品:矩形触点，24-28 AWG 特点:- 配用:H1505TR-ND - CONN SOCKET 24-28AWG CRIMP GOLDH1504TR-ND - CONN SOCKET 24-28AWG CRIMP TIN 相关产品:AP105-DF11-2428S(64)-ND - TOOL APPLICATOR DF11 ACCESSORIESAP105-DF11-2428S(63)-ND - TOOL APPLICATOR DF11 ACCESSORIESAP105-DF11-2428S(62)-ND - TOOL APPLICATOR DF11 ACCESSORIESAP105-DF11-2428S(61)-ND - TOOL APPLICATOR DF11 ACCESSORIESCM-105 WITH TRANSFORMER-ND - TOOL AUTO CRIMPING MACHINE 其它名称:*AP105-DF11-2428SQ1139807AQ949366 |
发布紧急采购，3分钟左右您将得到回复。