- 您现在的位置：买卖IC网 > PDF目录152475 > 1-100645-01 (SENSITRON SEMICONDUCTOR) DIGITAL TEMP SENSOR-SERIAL, 14BIT(s), SQUARE, SURFACE MOUNT PDF资料下载
参数资料
| 型号： | 1-100645-01 |
| 厂商： | SENSITRON SEMICONDUCTOR |
| 元件分类： | 温度/湿度传感器 |
| 英文描述： | DIGITAL TEMP SENSOR-SERIAL, 14BIT(s), SQUARE, SURFACE MOUNT |
| 封装： | ROHS COMPLIANT PACKAGE, 6 PIN |
| 文件页数： | 9/12页 |
| 文件大小： | 332K |
| 代理商： | 1-100645-01 |
Datasheet SHT21
www.sensirion.com
Version 1.1 – May 2010
6/12
3 Interface Specifications
Pin Name
Comment
1
SDA Serial Data, bidirectional
2
VSS Ground
5
VDD Supply Voltage
6
SCL Serial Clock, bidirectional
3,4
NC
Not Connected
Table 2 SHT2x pin assignment, NC remain floating (top view)
3.1
Power Pins (VDD, VSS)
The supply voltage of SHT2x must be in the range of 2.1 –
3.6V, recommended supply voltage is 3.0V. Power supply
pins Supply Voltage (VDD) and Ground (VSS) must be
decoupled with a 100nF capacitor, that shall be placed as
close to the sensor as possible – see Figure 11.
3.2
Serial clock (SCL)
SCL is used to synchronize the communication between
microcontroller (MCU) and the sensor. Since the interface
consists of fully static logic there is no minimum SCL
frequency.
3.3
Serial SDA (SDA)
The SDA pin is used to transfer data in and out of the
sensor. For sending a command to the sensor, SDA is
valid on the rising edge of SCL and must remain stable
while SCL is high. After the falling edge of SCL the SDA
value may be changed. For safe communication SDA shall
be valid tSU and tHD before the rising and after the falling
edge of SCL, respectively – see Figure 12. For reading
data from the sensor, SDA is valid tVD after SCL has gone
low and remains valid until the next falling edge of SCL.
Figure 11 Typical application circuit, including pull-up resistors
RP and decoupling of VDD and VSS by a capacitor.
To avoid signal contention the micro-controller unit (MCU)
must only drive SDA and SCL low. External pull-up
resistors (e.g. 10kΩ), are required to pull the signal high.
For the choice of resistor size please take bus capacity
requirements into account (compare Table 5). It should be
noted that pull-up resistors may be included in I/O circuits
of MCUs.
See Table 4 and Table 5 for detailed I/O
characteristic of the sensor.
4 Electrical Characteristics
4.1
Absolute Maximum Ratings
The electrical characteristics of SHT2x are defined in
Table 1. The absolute maximum ratings as given in Table
3 are stress ratings only and give additional information.
Functional operation of the device at these conditions is
not implied. Exposure to absolute maximum rating
conditions for extended periods may affect the sensor
reliability (e.g. hot carrier degradation, oxide breakdown).
Parameter
min
max
Units
VDD to VSS
-0.3
5
V
Digital I/O Pins (SDA, SCL)
to VSS
-0.3
VDD + 0.3
V
Input Current on any Pin
-100
100
mA
Table 3 Electrical absolute maximum ratings
ESD immunity is qualified according to JEDEC JESD22-
A114E method (Human Body Model at 4kV), JEDEC
JESD22-A115A method (Machine Model 200V) and
ESDA
ESD-STM5.3.1-1999
and
AEC-Q100-011
(Charged Device Model, 750V corner pins, 500V other
pins). Latch-up immunity is provided at a force current of
100mA with Tamb = 125°C according to JEDEC JESD78.
For exposure beyond named limits the sensor needs
additional protection circuit.
4.2
Input / Output Characteristics
The electrical characteristics such as power consumption,
low and high level input and output voltages depend on
the supply voltage. For proper communication with the
sensor it is essential to make sure that signal design is
strictly within the limits given in Table 4 & 5 and Figure 12.
Parameter
Conditions
min
typ
max
Units
Output Low
Voltage, VOL
VDD = 3.0 V,
-4 mA < IOL < 0mA
0
-
0.4
V
Output High
Voltage, VOH
70%
VDD
-
VDD
V
Output Sink
Current, IOL
-
-4
mA
Input Low
Voltage, VIL
0
-
30%
VDD
V
Input High
Voltage, VIH
70%
VDD
-
VDD
V
Input Current
VDD = 3.6 V,
VIN = 0 V to 3.6 V
-
±1
uA
Table 4 DC characteristics of digital input/output pads. VDD =
2.1V to 3.6V, T = -40°C to 125°C, unless otherwise noted.
SDA
SCL
GND
VDD
MCU (master)
RP
SCL OUT
SDA OUT
SDA IN
SCL IN
C
=
10
0n
F
SHT2x
(slave)
1
6
5
2
4
3
相关PDF资料 |
PDF描述 |
|---|---|
| 1-102154-0 | 50 CONTACT(S), MALE, STRAIGHT TWO PART BOARD CONNECTOR, SOLDER |
| 1-102154-1 | 60 CONTACT(S), MALE, STRAIGHT TWO PART BOARD CONNECTOR, SOLDER |
| 1-102154-2 | 64 CONTACT(S), MALE, STRAIGHT TWO PART BOARD CONNECTOR, SOLDER |
| 1-102321-0 | 50 CONTACT(S), MALE, STRAIGHT TWO PART BOARD CONNECTOR, SOLDER |
| 1-102321-1 | 60 CONTACT(S), MALE, STRAIGHT TWO PART BOARD CONNECTOR, SOLDER |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 1-100645-3 | 功能描述:端子 250 FL.LIF FAST.REC RoHS:否 制造商:AVX 产品:Junction Box - Wire to Wire 系列:9826 线规:26-18 接线柱/接头大小: 绝缘: 颜色:Red 型式:Female 触点电镀:Tin over Nickel 触点材料:Beryllium Copper, Phosphor Bronze 端接类型:Crimp |
| 110-065-000 | 制造商:VDC 功能描述:LEAD BNC PLUG PLUG 75OHM BLACK 5M 制造商:VDC 功能描述:LEAD, BNC, PLUG PLUG, 75OHM, BLACK, 5M, Connector Type A:BNC Plug, Connector Type B:BNC Plug, Cable Length - Imperial:16.404ft, Cable Length - Metric:5m, Jacket Colour:Black, Impedance:75ohm |
| 11-006502-000 | 制造商:Amphenol Corporation 功能描述:11-006502-000 - Bulk |
| 11-006506-000 | 制造商:Amphenol Corporation 功能描述:11-006506-000 - Bulk |
| 11-006509-000 | 制造商:Amphenol Corporation 功能描述:11-006509-000 - Bulk |
发布紧急采购，3分钟左右您将得到回复。