- 您现在的位置：买卖IC网 > PDF目录18501 > 1-1490413-4 (TE Connectivity)TOOL NEST DIE HD SEAMLESS 8AWG PDF资料下载
参数资料
| 型号： | 1-1490413-4 |
| 厂商： | TE Connectivity |
| 文件页数： | 4/5页 |
| 文件大小： | 0K |
| 描述： | TOOL NEST DIE HD SEAMLESS 8AWG |
| 标准包装： | 1 |
| 压接或电缆尺寸： | 8 AWG |
| 压接手柄： | 1490748-1，1490749-1 |
| 连接器类型： | 端子及连接件 |
408- 10110
ACCEPT
Terminal
REJECT
1
3
4
4
1
2
6
2
3
1
Splice
4
1
3
2
4
3
2
5
1
2
3
4
Crimp is centered on wire barrel. Crimp may be off
center but not off end of wire barrel.
Wire size being used matches the wire range or size
stamped on terminal or splice and dies.
Wire insulation does not enter wire barrel.
End of wire is visible through sight hole of terminal or
splice.
1
2
3
4
5
5
Crimp is off end of wire barrel.
Wire size being used does not match the wire range
or size stamped on terminal or splice and dies.
Wire insulation enters wire barrel. Check that the
strip length is correct.
End of wire is not visible through sight hole of terminal
or splice. Wire was not inserted far enough.
Excessive “flash” on terminal or splice. This indicates
damaged dies or wrong wire size, splice, or tooling com-
bination was used.
Nicked or missing strands.
Figure 5
2. Check all surfaces for wear. Inspect the crimp
area for flattened, chipped, cracked, worn, or
broken areas. If damage is evident, the die must
be replaced. Refer to Figure 6.
B. Gaging the Crimping Chamber
This inspection requires the use of a plug gage
conforming to the dimensions in Figure 7. Refer to
Figure 7, and gage the crimping chamber as follows:
Pitted
Flattened
Chipped
Broken
1. Mate the dies until it is evident that they have
bottomed. Hold the dies in this position.
2. Align the GO element with the wire barrel
crimping chamber. Push the element straight into
the the crimping chamber without using force. The
GO element must pass completely through the
crimping chamber.
4 of 5
Figure 6
3. Align the NO--GO element and try to insert it
straight into the same crimping chamber. The
NO--GO element may start entry but must not pass
completely through.
Rev D
相关PDF资料 |
PDF描述 |
|---|---|
| GKLA3D1A2-F03-C | SWITCH INTERLOCK SPDT SLOW ACT |
| QXRT12 | TOOL EXTRACTION 2.5MM |
| EVU-F3MFL3D24 | POT 20K OHM 9MM VERT MET BUSHING |
| ASEMPC-100.000MHZ-Z-T | OSC 100.000 MHZ CMOS MEMS SMD |
| 3310C-101-104L | POT 100K OHM 9MM SQ PLASTIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 1-1490413-5 | 功能描述:手工工具 NEST HD SEAMLESS 6 RoHS:否 制造商:Molex 产品:Extraction Tools 类型: 描述/功能:Extraction tool |
| 1-1490413-6 | 功能描述:手工工具 NEST HD SEAMLESS 4 RoHS:否 制造商:Molex 产品:Extraction Tools 类型: 描述/功能:Extraction tool |
| 1-1490413-7 | 功能描述:手工工具 NEST HD SEAMLESS 2 & 1 RoHS:否 制造商:Molex 产品:Extraction Tools 类型: 描述/功能:Extraction tool |
| 1-1490413-8 | 功能描述:手工工具 NEST HD SEAMLESS 1/0 RoHS:否 制造商:Molex 产品:Extraction Tools 类型: 描述/功能:Extraction tool |
| 1-1490413-9 | 功能描述:手工工具 NEST HD SEAMLESS 2/0 RoHS:否 制造商:Molex 产品:Extraction Tools 类型: 描述/功能:Extraction tool |
发布紧急采购，3分钟左右您将得到回复。